VVSR1070DCWW Hotpoint Washer - Instructions

Repair went well but there was clips to the door switch not in the video. Still was easy to work around and complete.

Removed the front of the washer using a putty knife. Removed the old belt and used a shop-vac to c,San up the insides. Placed the belt on the pulley and used three med sized zip ties about one inch apart. I cut off the exposed tail of the zip ties. Got the belt started around and put the belt onto the small pulley. Keeping an eye on the small pulley to make sure the belt did not slip off, I had to push it up a time or two. Then as I pulled the big pulley around, one zip tie broke, replaced it and continued pulling the big pulley, it got tough but with one knee pushing on the drum and pulling with one had it went on. I did slowly turn it to align the belt on the big and small pulleys. Not hard, I recommend a bright flashlight and gloves. I saved a good buck doing it myself :-)

First removed tub comming from Tub and removed srcew to replace. Has to twist part out of slot to remove installed in reversed order. Really easy to do.

Removed the front cover with a screwdriver, by locating and slightly prying the metal clpis back to release the cover. Then I removed one screw (only one visible) from the strap that hold the top cover/lid down. With a little prying, I lifted the lid up out of the way, and suspended it with a cord. I removed the old dampener straps and replaced each one at a time with the new strap. It was not to hard to get to the screws (I have large arms), and it only took me nearly a half hour to complete the task. It would have been easier if I used two different size nutdrivers, but it was easy enough with an adjustable wrench. Then simply put everything back to together in reverse order of how I took it apart. The wife was impress that I fixed another thing around the house.

I had to replace the water fill nozzle on my GE washer, and having the instruction video on the parts page is a real time-saver. It shows how to remove each part on your washer in order to access the area where the part needs to be replaced. Start to finish, about 20 minutes. Easy peasy.

Removed the knob from water level switch. Removed 4 screws holding the control panel cover on and leaned it out. Made sure the washer was unplugged and removed the three wires and removed the water level hose and the switch. Installed the new switch and hose plugged the wires back in and put things back together. Washer works fine now.

First I found out on the web how to open the washer's front cover.
For the strap in the front, it's relatively easy to replace a strep if your hands are somewhat flexible.
For the one in the back, I also needed to open the top dial panel, in order to lift the main lid connected to it, in order to then be able to reach one of the screws of the back strap. the other one of its screws I was able to reach from the front with a ratchet and extension from the front. Arms do get heavy from time to time, but overall it was manageable.

The after school director told me of the washing machine flooding. It took only a bit to find the hose that was leaking--a little longer to figure out where it went. It was the bleach line to the drum from the little bowl under the lid. It had pulled off.

I noticed that three of the four tub dampening straps (little rubber bungees) were broken. PartsSelect had a good exploded view of the washer that helped me locate the correct part and order it. They were shipped quickly.

Start with the machine empty of water and unplugged.

The front of the washer pops off (most have a removable top but this GE did the front instead). This exposes two screws to remove in order to lift and remove the top, exposing the tub. While you lift the lid, you have to remove the bleach line from the pocket at the front of the machine. It helped to unplug the machine and remove the lid switch to make access easier. It has two screws holding the assembly to the lid.

The straps are on the four corners of the tub, attached by hex-head screws. The two in the back aren't as easy to access. A stubby nutdriver would have helped for the screws that were upside down holding the straps to the frame. The straps were replaced and all the parts put back.

The washer is quieter and shakes much less. It was ready for the Christmas dinner washing later in the week.

Reading all the other stories helped me get started. One tip I want to share is when removing the old coupler, I held on to a pulley puller by hand. I hooked the jaws underneath; while I pulled up on it, I would tap with a hammer on either side of the old coupler. This gave me the leverage needed to make it pop right off.

This was a easy job for the do it your selfer. I had no problem the part ,it was like the same one I took off. Now I know where to come for parts . It was perfect . Thanks again

Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.

I pulled the top off of the washer and found that my leak was coming from a small hole in the hose and water inlet. I had to remove 2 small bolts and a hose clamp to remove the old part,I did the reverse to install new part.

1- Shut off water and unplug unit
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out

15 minutes - 30 minutes tops!
Good luck Matt East Islip NY

e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) that were easy

I bought 3 parts for I didn't know what I need so I listen to the companies video twice.
I popped off the agitator which was easy. then had a little trouble with getting the screw/nut out it was rusty. Finally got that off then I worked backwards and I found I didn't need all the parts which I sent back with no problems. My machine works as good as new ,it has stopped making noise. I am really proud I did this by myself and didn't need my husbands help,

I also spent less than 12.00 to fix and a new one is over 600.00.

Thank You
Christine brooks