VWSR4150B0WW Hotpoint Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pamela from Wiscasset, ME
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Washer would not pump water out of basin
I purchased the part, watched the video that was embedded in the email I received, folllowed the instructions and was able to wash my laundry. It could not have been any easier unless the the part caem already installed. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from harwinton, CT
- Parts Used:
- WH41X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Leaking at housing
This was not hard to do.removed top screws and back plate screws. Water inlet valve has 3 screws and a hose clamp.this job was thirty min. tops.goes back together much faster then taking it apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gustavo from Harlingen, TX
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Shaking and making loud noise
removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Ridgeland, MS
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Water wasn't being pumped out.
The pump would stick and not pump the water out from time to time. I have removed the pump before and cleaned it so to replace it wasn't much different for me. The instructions on the web site were pretty straight and easy to follow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from SHIRLEY, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Water would not pump out of the unit or spin
If you follow the video that part select provides you will be just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Mansfield, OH
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
water pump died
Was easy. Removed pump, ordered yours and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from Rochester, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Leaking water on final pump out
Removed front panal & operate to see leak origion. Found the side of the pump cracked and split. Part Select sent the exact replacement part! Unplug washer. Remove ront panal; using a putty knife and a bit of preasure at the two release clips. Using pliers or small vise grips, squeeze hose clamps and locate back out of the way and remove two hoses. Have a shallow pan below to catch remainig water. Unhook the electric connections, taking note of where. Using nut driver or small ratchet, remove the two mounting screws and pump. I used new screw type hose clamps in lieu of the originals.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from RIDGE, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Washer was stalling in rinse cycle and not draining
Removed the front of the washer, screwdriver used. Disconnected the electrical wires from the pump. Removed the two bolts from the water pump bracket, socket wrench used. Disconnected the pump to exterior drain hose, plumbers wrench used to loosen tension clips. Drained all the water out of the washer tub, not easy not very neat. Disconnected the washer tub to water pump drain hose. Removed debris that was in the hose. Then connect the hoses to the new pump, bolted the bracket back in place, put the front of the washer back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Olle J from Albert Lea, MN
- Parts Used:
- WH2X1197
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Noisy washer, especially while spinning.
Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from bradford, VT
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
Tub would shake and the whole machine was threatening to jump
As the video described. The two rear dampening straps holding screws were only accessible from underneath making their installation much more difficult than the front ones which were accessible from the top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Cumberland, MD
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Would not completely drain all the water out of the tub after the final rinse cycle, with a burning smell from the belt because it could not turn properly.
I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from walkersville, MD
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
tub wouldn't drain
Easiest thing I ever did on the computer. U tube helped me diagnose the problem and how to remove the old pump and install the new. Parts Select menu was easy to navigate and had a picture of the pump I needed. The cost was affordable and I got the satisfaction of making the repair myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from woodland, CA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
3 of the 4 dampening straps were broken.
Watched the video from your web site and followed the instructions. Didn't need to remove the console on my model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from mazeppa, MN
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
broken dampening straps
removed front of washer and removed top of washer very easy to replace 4 dampening straps (2 straps were broken replaced all 4
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marci from Salt Lake City, UT
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
GE Profile Washer would not agitate but would still spin, etc.
I used the "belt" technique to remove the agitator. It was difficult at first to remove but after a few tugs on the belts that were looped under the plastic bottom, the agitator came up. Then I unscrewed the bolt holding the coupler. The agitator coupler kit purchased from PartSelect came with a new screw so I replaced the old coupler with the new one and fitted the new screw in it's place. I put the agitator dasher back on and then it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!