VWSR4150DCWW Hotpoint Washer - Instructions

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

Remove agitator. Remove coupling. Reinstall new coupling. Reinstall agitator. My only problem was the 7 day delay in getting the part. I expected 2-day delivery.

First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything back together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.

I followed the video from the website to install the lid switch. Worked like a charm. Great instructions. You do need to supply your own butt splice connectors .

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.

I removed agitator by pulling it up until it unsnaped.

I removed the old agitator coupling by removing the bolt and pulling up while twisting it.

The new coupling looks different than the old part but fits the same.

I pressed the new coupler on to the agitator shaft, reinstalled bolt and pressed agitator on the agitator coupler until it snaped into place.

Washer runs like new!

1.Pulled the agitator out. Unscrewed the top nut, which was a little tricky to break loose since it had been in place for over 10 years. Pulled out the entire washing cylinder to unscrew and replace the hub. Not bad but you need to take out the inner tub and that requires doing a little extra unscrewing and prying.

Our GE washer stopped agitating. We bought us a Whirlpool Cabrio washer with auto-sensing and an impeller instead of an agitator. My wife couldn't get used to washing clothes with so little water. We found out about PartSelect.com and ordered the part they indicated would probably fix our GE washer ($5.86) - the Agitator Coupling Kit. Ordered it on Friday, received it by Fed Ex the following Tuesday. It was an easy installation. Our GE is working fine. Took the Whirlpool back to the store, got our $637.00 back.I plan to use PartSelect.com again,if I need to. We don't like the new type washers as well as our 7-1/2 year old GE.

I researched what could be the problem in the internet and follow the instructions from a GE technician, I chose the problem from a list and followed the video the technician played on how to do it yourself. This time was the lid switch which is found visible under the lid opening usually right middle flush with the opening. When I got the new lid, only the switch gets bad so I cut the cable enough to replace the old one, pulled out and cut and connected the new one. If there is not enough cable use the spatula to push the clips on the front panel on the top both side about 5 inches from the corner and pull panel out front and now you can see the wires better and make the connection.

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

We pulled off the bottom cover to access the pump. The washer was on its back and that made it easier to reach. There was two hose clamps to pull off along with the two electrical parts. Very easy to replace.

Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!

After doing some troubleshooting, I found that the Air Bell was stripped inside.

First I removed the agitator by firmly pulling it straight up. Then I removed the bolt holding the air bell (agitator coupling) with a ratchet. Then came the hard part. The air bell (agitator coupling) was stuck on the shaft and would not come off. I used rope to lasso under the coupling and tied it to a 2x4 for leverage and eventually wrestled it off by using an upward jolting motion time and time again. Spraying WD-40 in the coupling seemed to help loosen it up.

Prior to installation, I cleaned the grooves of the shaft by scraping them out with a flat tip screw driver. Installed the new coupling by tapping it down with a hammer until it was seated firmly and locked it down with the new bolt. Aligned the agitator and slid it down until it latched. Done!

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

The repair would have gone well, however partselect sent me the wrong part. Instead of a washer belt, they sent me a door seal to what looks like a refrigerator