Models
>
VBXR2070T3AB
VBXR2070T3AB Hotpoint Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for VBXR2070T3AB
Viewing 4 of 4
Keep searches simple, eg. "belt" or "pump".
In Stock
Order now and your part arrives by Apr 6
$25.10
This hose clamp kit contains two clamps. The smaller of the two is an inch in diameter while the larger of the two is two inches in diameter.
In Stock
Order now and your part arrives by Apr 6
In Stock
Order now and your part arrives by Apr 6
Special Order
The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.
No Longer Available
Special Order
In Stock
Order now and your part arrives by Apr 6
In Stock
Order now and your part arrives by Apr 6
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for VBXR2070T3AB
Viewing 3 of 3Leaking
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Noisy and Marks Left on Clothes
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephen from Woodbridge, VA
- Parts Used:
- WH12X1043
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lid switch failed
First removed front washer access panel.
Next: removed top panel torx screws and disconnected lid switch wiring connector
Next: removed washer top/lid
Next: removed inoperative lid switch (two phillips head screws)
Next: installed new lid switch and screws
Next: installed washer top and connected lid switch wire c ... Read more onnector
Next: installed control panel and screws
Next: tested installation
Next: installed front washer access panel
Easy repair. FYI, Parts Select had best price and part arrived within two days of ordering! Highly recommend them for your parts.
Next: removed top panel torx screws and disconnected lid switch wiring connector
Next: removed washer top/lid
Next: removed inoperative lid switch (two phillips head screws)
Next: installed new lid switch and screws
Next: installed washer top and connected lid switch wire c ... Read more onnector
Next: installed control panel and screws
Next: tested installation
Next: installed front washer access panel
Easy repair. FYI, Parts Select had best price and part arrived within two days of ordering! Highly recommend them for your parts.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from College Station, TX
- Parts Used:
- WH44X1206
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rusty corner
The screws were rusted onto the old lid. It wasn't difficult to get the other site off. I used PB Penetrating catalyst and it came right off. You'll need to grab the little plastic poker thingy from the old lid, so don't throw that away.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Olle J from Albert Lea, MN
- Parts Used:
- WH2X1197
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Noisy washer, especially while spinning.
Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine
... Read more
until it completely fails.
Read less
Was this instruction helpful to you?
Thank you for voting!