VBXR1090DBWW Hotpoint Washer - Instructions

I put my fingers under the agitator and pull up , this pulled it off the couplier, then I used a 11mm wrench to remove the bolt that holds the couplier in place and pulled the couplier off, the new couplier didnt arrive until after I went to work but my wife had it all back together when I got back home,I told her what to do and she said it only took about 10 mins. to get together, very easy.

I first placed a rope under the fins of the agitator and used a 2X4 board to pull up the agitator which needed very little force to release itself from the agitator coupling. I removed the nut holding the agitator coupling, removed the stripped agitator coupling. Installation was just the reverse process, inserted the new agitator coupling, placed and tightened the screw, and pressed down the agitator over the agitator coupling and I was done. Over time for the repair was between 5 and 10 minutes, very easy, and I have no experience repairing washing machines.

took out the agitator then removed the agitator coupli and found out that the coupli was worn out, i then replaced it and everything worked again

Very easy with your great instructions in my email. took the wires off,took the hoses off,then the two bolts,put the new one on and reasembled the hoeses wires and bolts. put the front back on and that was that. Your company is great thanks for all your help.If I ever need help again with any off my appliances i will call on you,agin thank you very much. Frank!

I took off the front of the washer with two screw drivers. Removed the hose clamps with the pliers then removed the two screws with the nut driver and changed out the pump. Nothing to it. Easy fix, it works like new for $45 and 15 minutes.

removed back off washer, disconnected pump from washer tub, remove old pump in about 5 min, then installed new pump in less than 5 min. washer is working just fine wife thank me it was about 2 wks since the washer was down.

Pull front cover and changed pump. Your delivery of this part was remarkable. Thanks for such good service.

My wife calls me and says that the washer is not draining water so I was like "great"...here goes more money. After I tried draining, cleaning, checking for leaks, I looked up possible causes and came across the water pump. I have bought from parts select and I love this website so I jumped on here, found the causes, diagram, installation videos, and cheap parts. Added to cart, paid, and was here in about two days. I disconnected the electricity, opened the front lid, took off the two hoses, unscrewed the pump, swapped in the new one and hooked it back up. The washer works like new, took me about 10 minutes. Thanks Partselect!!!!

Shut off power, removed both water hoses, detached drain hose, noticed the plastic drain hose was splitting, entered the model number in a web search, ordered part from PartSelect. received part next day and reversed previous process. Tested repair and no leaks.

old one out, new one in. new one is seated, but not a perfect match bracket to hold hose in washer does not fit on this replacement hose properly. But I feel comfortable with the result & use

Unpluged from out let. the I just took the front off then I took the bolts out of the mounting bracket and the took the hoses off unpluged the plug. We pluged the plug in the new piece put the hoses back on rebolted the braket down put the front on and plug the eletric back in and did the load thank you soo much

1) Remove the load size dial by simply pulling it off gently. 2) To gain access to the switch, you must remove the "splash panel" where the dials are located. Do this by removing 3 hex screws from the back of the splash panel. **(If you need to move the washer, do so with the tub empty. This will make it easier to move and also lessen the chance of damaging the floor due to excess weight - water weighs 8 lbs per gallon - the average washer hold from 10-15 gallons on the largest load). 3) Once you have access to the rear of the panel, you will notice 3 hex-head screws holding the splash panel to part of the galvanized metal washer frame. Remove these screws and make sure you place them where you won't lose them. Slide the back splash section to the right a little and then lift the back splash away from the washer. 4) Remove the plastic tubing located on the brown/orange section of the switch. 5) Now, gently press the female connector from the switch by gently pushing it away from the area where the tubing was and pull at the same time. 6) To remove the switch from the back splash, turn the switch in a clock-wise direction (do this carefully so the delicate section of the back splash doesn't break.) 7) Inspect the tubing to see if it has expanded while being on the pressure switch - If so, use a very sharp knife (carefully) to cut off that old piece. 8) Take the new switch and install it by getting it in the correct position (you can tell because the metal frame of the switch has two ears that help you to align the switch correctly) Twist the switch in a anti-clockwise direction until it snaps in place. 9) This step can be skipped if the "snap in place" works and the switch is firmly seated. IF, at some time or other, the nubs that are used to hold the switch in place have been damaged, you will have to replace the back splash (Prt # PS2340063) and this costs more than the switch. 10) If you are here without reading step 9 - Congratulations! 11) Make sure you replace the electrical connector onto the new switch (it only fits one way so if at first you are having trouble, try turning the connector 180 degrees. Once all the parts you disconnected from the pressure switch are back in place properly, place the back splash back onto where it came from. Replace the 3 hex-screws that hold the back splash to the machine and before replacing the machine to where you pulled it out from, run a test to get the pressure switch "pressurized." My suggestion is to set the switch at the setting where the water only fills for a medium load. (This next part is not necessary but is eco-friendly) Set the other dial so you only are using COLD water. Start the water loading into the tub (DO NOT have any material in the tub or the switch will not be set properly) and watch the water level to make sure it shuts off at the correct level. If not, don't worry, Just shut the machine off and turn the dial to Spin to empty the water. Do this while the lid is closed so you can tell when all the water has been emptied; there will be an unmistakable change in the sound of the pump. Start the COLD cycle over again and watch the water level; it may shut off the flow if the pressure switch has been pressurized correctly. If not, repeat the procedure once more. Again, if it shuts off properly, you can now try a load of clothes (keep it at the medium setting). After the clothes have gone through the complete cycle, the pressure switch may have reset itself and the next load will seem to have less water. Simply set the water level to its highest level and you are now all set to wash all the towels you used to soak up the water from the overflow. ONE MORE THING - If the pressure switch doesn't fix the problem, you will need to replace the valve assembly.

Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.

Removed the front of the washer, screwdriver used. Disconnected the electrical wires from the pump. Removed the two bolts from the water pump bracket, socket wrench used. Disconnected the pump to exterior drain hose, plumbers wrench used to loosen tension clips. Drained all the water out of the washer tub, not easy not very neat. Disconnected the washer tub to water pump drain hose. Removed debris that was in the hose. Then connect the hoses to the new pump, bolted the bracket back in place, put the front of the washer back on.

Remove top of washer control panel to access filler. My hands are not large by t was difficult removing the old part and carefully trying not to drop mounting screws. Had to loosen screws twisting threads with pliers. No access for regular Phillips screwdriver. Patience is needed.