Models > VVSR1030H3WO > Instructions

VVSR1030H3WO Hotpoint Washer - Instructions

Jump to:

All Instructions for the VVSR1030H3WO
121 - 135 of 260
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Richard from Ridgeland, MS
Parts Used:
WH23X10030
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
Water wasn't being pumped out.
The pump would stick and not pump the water out from time to time. I have removed the pump before and cleaned it so to replace it wasn't much different for me. The instructions on the web site were pretty straight and easy to follow.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Terrance from Eldom, MO
Parts Used:
WH01X39337
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Socket set
A banging noise while the machine was washing.
The repair was done like the video suggested to do and in the order. And it worked well.In the step by step procedure.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dale from Wrightwood, CA
Parts Used:
WH23X10030
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
wouldn't pump water
I followed the step by step video on how to install the pump..I am 70 years old and female..it was very easy to install..your company is A+..sure liked the savings doing it myself..
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
james from baltimore, MD
Parts Used:
WH23X10030
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
Bought the unit used and noticed when i opened the front of the washer indications of the pump leaking and some rust on the pump/motor bracket.
First i noticed a small leak coming from the pump assembly dripping onto the motor/pump bracket with indications that it had been doing this for some time.Looking @ this i then took the pump/motor assembly off cleaning the inlet and outlet of pump off so i could plug one side of the pump while blowing into the inlet side of the pump verifying that the gaskets around the pump assembly was in fact leaking.Replacement was very easy.Purchased a new pump/motor assembly from parts select and received it in three days.Used a flat tip screw driver to press on top front clips pulled away from front of washer then up and off.The pump/motor assembly only has two screws holding it down then i pulled off the electrical connector after that used channel locks to remove both inlet and outlet hoses off pump.Installed new. very easy
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
larry from Steamboat Springs, CO
Parts Used:
WH01X39337
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
broken tub strap
follow youtube vid. simple
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Danny from Clarksdale, MO
Parts Used:
WH23X10030
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
Washer would not drain or Spin!
First I unplugged the washer and then removed the front panel of the washing machine using the puddy knife running it along the top edge approximately 3 inches inward from each corner found the tab on each end and pushed in with the knife until the panel popped loose from the top tabs. I then located the pump motor on the lower front right side of the machine and compared it to the new one that I had purchased,(they were the same) Note;be sure all the water is drained from the washer otherwise get ready for a bath approximately 1 gallon of water came out of the drain hose that is located on the back of the pump after using the pliers to squeeze the clap and remove the hose,this was the worst of the whole job,then remove the inlet hose on the top by squeezing the spring clamp with the pliers. Next unplug the harness located in the front of the pump,and then last take a 1/4 drive ratchet w/extension and a 10 mm socket and remove the 2 hex screws on the mounting plate. Install the new pump and motor assembly in reverse order with the instructions above and you should be washing clothes in no time. Thanks
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pamela from Wiscasset, ME
Parts Used:
WH23X10030
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Washer would not pump water out of basin
I purchased the part, watched the video that was embedded in the email I received, folllowed the instructions and was able to wash my laundry. It could not have been any easier unless the the part caem already installed. Thank you.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
dennis from harwinton, CT
Parts Used:
WH41X10077
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
Leaking at housing
This was not hard to do.removed top screws and back plate screws. Water inlet valve has 3 screws and a hose clamp.this job was thirty min. tops.goes back together much faster then taking it apart.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gustavo from Harlingen, TX
Parts Used:
WH01X39337
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Shaking and making loud noise
removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Arlis from Moore, SC
Parts Used:
WH01X39337
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Tube Shaking Like Out Of Balance. Water Not Draining Completely And Created An Unpleasant Odor
Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Nampa, ID
Parts Used:
WH23X10030
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Wouldn't pump water
Removed the old pump put in the new one
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Timmy from Fairport, NY
Parts Used:
WH01X39337
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Banging noise when it was agitating
removed front washer cover (2) clips at top released with straight screwdriver . removed washer top cover (2) 1/4" head screws that are behind front washer cover. Then removed screws holding tub dampening straps (4)5/16" head from agitation drum housing from top, removed other end of strap from under side (4) 1/4" head screws. then assembled with new straps in reverse order. easy repair nice and quiet again.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Belinda from FLORENCE, KY
Parts Used:
WH41X10096
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
cracked drain pipe
Remove two bracket screws. Removed hose. Put new hose in place using same bracket and screws. inserted end of hose into washer drain. Secured hose to cold water hose with two zip ties.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Priscilla from Beverly, MA
Parts Used:
WH01X39337
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Socket set
broken dampening strap
Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Eddie from Spotsylvania, VA
Parts Used:
WH23X10030
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
would not drain
watched Partselect video and followed instructions step by step
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the VVSR1030H3WO
121 - 135 of 260