VLXR1020A2WO Hotpoint Washer - Instructions

The repair was done as describe by others with the "hub nut" having to be cut off due to corrosion. Instructions for removal of the tub were found inside the control panel area on the left hand side. Ordering s new hub nut and cutting off the old one proved to be a necessity.

The first thought regarding the light rumble during the spin cycle is that the bearing was going bad. Many of the other inputs on replacing the bearing included the problem with removal of the Hub Nut. Only one article noted a set of assembly instruction for the washer is clipped onto the upper rear panel behind the control knobs, but I did not see this comment until later. Not being sure where to start with diassembling the washer, I began by taking off the control panel and to my pleasant surprise I found a neatly folded set of detailed instructions. Following the instructions, I proceeded to quickly disassemble the washer until I got to the HUB NUT. The Hub Nut is an aluminum, 1 -11/16 inch, left hand threaded problem. My tool selection is somewhat limited, so after unsuccessfully attaching it with grippers and vice grips, supported with the liberal aid of a rubber mallet and plenty of WD40, I went looking for something with which I could a better grip on the hub nut. The grippers and vice grips would slide a bit when hit with the mallet. Also since the space is very restricted, a large wrench could not be used. I located a 9-inch pipe wrench, and with the rubber mallet the Hub Nut finally loosened after just a few hits. I replaced the old bearing which appeared to be in fair condition. While replacing the bearing has not solved my noise problem, I thought that my experience with the pipe wrench benefit someone else in their efforts to get the hub nut off without using a chisel.

Removed the screws, pulled out the tall skinny thing that rotates, pulled out the broken part, ordered the new one, replaced it, (you have to push down until it snaps into place) Put everything back together and had clean laundry within 45 minutes. Anyone can replace this part.

I used the "belt" technique to remove the agitator. It was difficult at first to remove but after a few tugs on the belts that were looped under the plastic bottom, the agitator came up. Then I unscrewed the bolt holding the coupler. The agitator coupler kit purchased from PartSelect came with a new screw so I replaced the old coupler with the new one and fitted the new screw in it's place. I put the agitator dasher back on and then it worked perfectly.

Removed front cover, disconnected wires and hoses, reversed process

took the two screws that holds the instrument selections off retreived the directions from inside this panel and followed directions step by step and removed the spline that makes the machine agitate, seen that the inside of the spline was smooth, ordered part and reversed operation in putting it back together.
p.s. make sure the refill shutoff hose is connected as we had forgot to do this and we ran water on the floor, had to take back apart and re-connect thehose .

ordering the part and fixing it myself with my sons help saved me a repair bill which I am sure would have cost me at least $75.00 more.

Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.

Remove top of washer control panel to access filler. My hands are not large by t was difficult removing the old part and carefully trying not to drop mounting screws. Had to loosen screws twisting threads with pliers. No access for regular Phillips screwdriver. Patience is needed.

Removed the front of the washer, screwdriver used. Disconnected the electrical wires from the pump. Removed the two bolts from the water pump bracket, socket wrench used. Disconnected the pump to exterior drain hose, plumbers wrench used to loosen tension clips. Drained all the water out of the washer tub, not easy not very neat. Disconnected the washer tub to water pump drain hose. Removed debris that was in the hose. Then connect the hoses to the new pump, bolted the bracket back in place, put the front of the washer back on.

Take off front. Take off top. Pull off agitator. Pull off agitator coupler, after removing bolt holding in place. Attempt to remove hub nut, no joy. Wound up cutting the nut with a Dremel tool and chiseling the nut off. Closer inspection revealed a bad transmission. Due to the cost of the transmission, we will continue to use the machine until it completely fails.

As the video described. The two rear dampening straps holding screws were only accessible from underneath making their installation much more difficult than the front ones which were accessible from the top.

Watched the video from your web site and followed the instructions. Didn't need to remove the console on my model.

Easiest thing I ever did on the computer. U tube helped me diagnose the problem and how to remove the old pump and install the new. Parts Select menu was easy to navigate and had a picture of the pump I needed. The cost was affordable and I got the satisfaction of making the repair myself.

I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!

removed front of washer and removed top of washer very easy to replace 4 dampening straps (2 straps were broken replaced all 4