VLSR1090G2WW Hotpoint Washer - Instructions

Watched the video, good video. But instead of taking the bolts out first, it's easier to remove bolts last, to give support to remove the hoses.

replaced them & working fine now....

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

This was one easy job and saved me money by doing it myself, First I unplugged the washer for safety, then I removed the Agitator by grabbing the base of the agitator with both hands and pulling up I set the agitator a side and removed the one bolt holding the agitator coupling in place. the replacement coupling was a little tight when I replaced it due to it being new, (make sure the coupling is fully seated before installing the bolt) reinstalled the agitator plugged the washer back in and tested repair worked flawlessly thanks partselect

The picture of how to depress the clips to remove the front was incorrect. The clips are 4" from the sides not immediately at the sides per the picture. The 4 rubber springs were only part of what was needed for the washer. The old gas dryer was still working. There are two more springs on the bottom of the tub missing not shown on diagrams, so it still sways side to side, bangs around and makes a lot of noise. After putting on the 4 rubber springs, it ran, but probably needed a new clutch also, because it wouldn't spin dry anymore. I ended up spending $2000 for new washer and dryer from Maytag, and throwing out these old machines today.

Pulled the agitator off by hand. Loosened the screw on top of the coupling and pulled old coupling off by hand. Replaced part with new coupling and socketed it in place. Replaced agitator by-hand by simply pushing it down on top of coupling making sure the plastic teeth aligned.

Watched a how to video. Pulled the agitator. Determined that the agitator coupling was worn out. Matched the old agitator coupling to new replacement one. Ordered it. Pushed the new agitator coupling onto the fitting. Secured it with the old bolt. Replaced the agitator. Repaired.

I had to take out the front panel to access the Tub. Afterward the work wasn't hard.

The hardest part is lifting the washer to get a the bottom. Disconnect the power, shut off water. Disconnect hoses and drain hose. Move washer from the wall about 2 feet. Tilt up front of washer. I used 4 12" long 8x8 inch lumber, lift washer….place one on each from corner. Lift again, place 1 more 4x4 on each existing 4x4. Now remove the belt off the 3 pulleys. Use the flat blade screw driver to remove the C clip holding the Pully on the shaft, with the flat bladed screw driver and hammer. Once the C clip is off remove the metal washer, pulley, plastic lock (apart of the bottom of the pulley & the thrush bearing and it's washer. Using the parts supplied (the "new thrush bearing is a bearing and washer combined) replace as you removed it. Thrust bearing, pulley, washer and, c clip. I tapped mine on using the flat bladed screw drive……becareful not to break it (they did supply 2 for me in the repair packet) make sure he c clip is secured. Lower the washer after removing all the tools from under the washer, by reversing the lift sequence. Slide the washer in place. Connect the hoses back up. Plug it in.Reconnect the drain hose, you should be good to go.

Ordered new pump on Sunday - replaced on Wednesday. Removed front washer panel with putty knife to release latches. Used pliers to disconnect hose clamps. Lots of paper towels to sop up water in bottom of washer and on floor. Unhooked electrical wires. Socket to remove pump. Reverse actions to replace pump. It's "plug and play"!

I paid over $100 several years ago to have this same repair done by an appliance repairman. I did it myself this time for less than $20. Definitely watch the installation video before you start. Remove agitator by pulling it up by its bottom flange (protect your face in case it pops off suddenly). Remove bolt holding agitator coupling onto the transmission shaft. Pull up on old coupling and remove it. Clean grooves on transmission shaft and then install new coupling over the shaft. Reinstall old bolt and the agitator following video instructions on lining up agitator on the coupling. Note: Standard Fedex Smartpost shipping took 6 days to go from Louisville, Kentucky to western North Carolina. If you're in a hurry it's worth it to pay for expedited shipping. Lots of dirty laundry piles up in a week!

remove top control panel & r&r water level/pressure switch.

Could have removed debis in old pump. Kept it as a spare.
Replacement was simple , (two nuts) & (2 Lg. Hose Clamps) + two wires.
Dealer wanted $168.00 Labor + $67.00 for part!.

Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!

I followed instructional video on partselect.com, it was very easy, but it didn't take care of the problem. I got to to order "TRIPLE WATER VALVE" and that did the trick. After opening the washer first time (for water fill nozzle), it took me even less time. You don't have to take the front panel off to replace the water valve.