A1408010 Hoover Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Hinge Pin
I followed the feed back in the forum from a previous repair. I popped open the top of the Washing and propped it open @ approx. 70 degrees,moved the Tub out of the way and used a small Phillips Scwdrvr to remove the broken part, installing the new parts was a snap, I took the time to use a Q-Tip and petroleum jelly to coat the pin and hinge making it easier and less binding when opening the lid.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Elizabeth, NJ
- Parts Used:
- WP35-6465, WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Made noise during washing and rinse cycle
It was easy to replace the water pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lon from Morton Grove, IL
- Parts Used:
- WP35-6465
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Socket set
Water pump replacement
Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump
Reverse the process to install a new pump
Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.
The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.
This was is 1st time we used your server but it won’t be the last!
Kudos to the entire staff and please…keep up the good work.
Sincerely,
Lon Thomas
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILL from DIX, IL
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The Pump Went Out & Water Was All Over My Floor..
Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Modesto, CA
- Parts Used:
- WP35-6465, WP21352320
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Washing machine began making a screeching noise but only during the spin cycle - when it was emptying the water from the tub. After a few uses the machine just stopped working.
The pump was easy enough to replace. Access panel in the back and 3 screws and it was off and back on in less than 20 minutes. It was putting the belt on that gave me the most trouble even though one of the pulleys moved to allow for easy replacement it did not move enough. It took me another 30 minutes just to get the belt on. I finally decided to place the belt on the two smaller pulleys and save the larger one for last and it went on with no trouble at all. Learn from my error =]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from CHULA VISTA, CA
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
water not draining
changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from East Brunswick, NJ
- Parts Used:
- WP35-2045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lid hinge pin broken
Opened hinges top of washer. Removed screws holding hinge bases. Removed the washer top lid and unscrewd broken hinge pin. Replaced hinge pin and inserted in pin base and screwd base op hinge back onto washer and job was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hollee from Rancho Mirage, CA
- Parts Used:
- WP21002026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Washer making loud noise and tub off balance
I followed Gary from Sioux City IA instructions. Very well explained.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Wading River, NY
- Parts Used:
- WP21002026
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Socket set
noisy out of balance during spin cycles
I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Moneta, VA
- Parts Used:
- WP35-6465, WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Made noise on spin cycle
Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
Lid hinges wear out, causing lid to slam as you are trying to put clothes in or take them out.
Lift the top of the washer so you can access the screws that hold the hinges. Replace the hinges,and close the washer top. This is the sescond time we have had to replace the hinges.
This lid and hinges are very poorly designed. Instead of opening to the side, it opens straight back. That means when the hinges wear out (and they do because they are plastic), you have to push the lid all the way back to stay open. When you push it all the way back, it hits the control knob and turns off the water.
If you are like me, I like to turn the water on and add the soap so it can dissolve before I add the clothes. It is really irritating when you open the lid and the only way for it to stay open is to push it all the way back and the water shuts off. And if you don't push it all the way back, it slams and scares the bejeebers out of you or slams on your fingers.
This lid and hinges are very poorly designed. Instead of opening to the side, it opens straight back. That means when the hinges wear out (and they do because they are plastic), you have to push the lid all the way back to stay open. When you push it all the way back, it hits the control knob and turns off the water.
If you are like me, I like to turn the water on and add the soap so it can dissolve before I add the clothes. It is really irritating when you open the lid and the only way for it to stay open is to push it all the way back and the water shuts off. And if you don't push it all the way back, it slams and scares the bejeebers out of you or slams on your fingers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Lebanon, PA
- Parts Used:
- WP35-6465
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Started making loud screeching noise(bad Bearing)
Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachelle from Eagle Mountain, UT
- Parts Used:
- WP43-0057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer wouldn't spin because the switch on the lid broke
I unscrewed the old lid switch and screwed on the new switch in seriously 2 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Virginia from Rockford, IL
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
machine was starting to make noises when spinning
My husband unhooked the water lines, unplugged the washer and remove the waste water hose, then we tipped it over and easy as pie the belt came off and the new one went right back on. I did not see any tears or breaks in the old belt, but it was stretched out a bit, and the washer is once again quiet. This also gave me an opportunity to clean under the washer, which we all know we don't do unless we have to. Cheap, quick, and easy fix for someone to do there self.
Was this instruction helpful to you?
Thank you for voting!