A1410 Hoover Washer - Instructions

Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the machine up . Worked perfect.











the

I removed the cover on the back of the machine, detatched the 2 hoses and removed the 3 screws holding in the Vertical Style Pump - with pulley. These screws are 10 mm nut-driver. The cover if I remember correctly was a standard rather than metric so make sure you have both available.

Screwed new part in, re-attached hoses and replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.

Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.

first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it a test then let the wife do a load of wash it worked like new

First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both sides. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking

I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nutdriver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.

I raised the top of the washing machine per video instructions, removed the screws, replaced broken hinges with the new ones. It was simple as that.

I used the putty knife to release the spring clips on the machine lid. They are about 3" in from the side of the machine. Then I lifted the top of the washer up holding the lid in place. I then used a screw driver (torx) to remove the hinge from the bottom of the washer top. The lid should come right off. Then I the removed the broken hinge pins from the back of the lid with a screwdriver and replaced with the new parts. There is a little tab that the pin fits in the lid to assure you have the pin installed correctly. Then I slid the hinge back on the pin and reversed the process reinstalling the hinges and closing the top of the machine over the spring clips and your done. Very easy repair that I completed in less than 15 minutes.

Easy repair - with the use of a phillips screwdriver, simply remove the old device and replace with the new

I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks

The lid switch is on the right side top of the washer under the lid. I took a putty knife and found the clips that hold the top of the washer and pushed them to release it. I then lifted it up to fully see the lid switch. I unplugged the washer from the wall socket and took out the 2 screws that holds the lid switch in. Then unplugged the lid switch from its electrical connection and put the new one in its place. Washer is working great so far.

I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!

Followed the great instructions on your video

1. Remove 1 screw holding each of 2 Hinges - use T15 driver. 2. Push tub to one side to get access to each screw from underside. 3. remove & replace broken Hinge Pin from Lid with T15 driver. 4. Drive broken pin out of the Hinge with a punch & hammer. 5. Install new Hinge Pin to Lid. 6. Add a little Vaseline to Hinge Pin & slide Hinge Pin into Hinge. 7. Line up Hinges to holes & re-install both Hinges with Lid. Have somebody help hold the Lid in a slight angle will make re-installation easier.

Disconnect all water supply and unplug washer. Remove 3 screws on back panel of the washer. This will expose the pump unit. Detach belt on the bottom of the washer. Then detach two hoses that connects to the pump unit. Use pliers if necessary to disconnect hoses. Use 5/16 socket with extension to take out three bolts the connect pump to the washer. That's it, now replace old pump unit and with new. Place bolts back in the 3 holes, reattached hoses, cover the back with 3 scres. Connect the belt to the pulley system on the bottom. Connect water supply and plug it in.

I had my 12 year old son climb to the back and he took off all the screws necessary in the back and took the part completely off. We ordered the part and waited for it to come in. We replaced the part, the screws and honestly, the only thing we had trouble with was replacing the small cover where the hoses stick out of the washer. Was an easy efficient experience that may have saved me $300.00+ dollars. Thanks to my 12 year old son we got her fixed up. The washer works like brand new.