GWS645RBS0 Gibson Washer - Instructions

Removed screws at back securing top panel (4).

Removed screws holding water inlet valve to back of machine (2)

Removed water hoses to bucket

Removed squeeze clamp securing water distribution hose from inlet valve

Reversed method with new valve.

Very fast...~25 min
Works fine so far!

released hold down clips on top and removed two screws at the bottom of the front panel and firmly pushed down on the panel to release it exposing the motor drive assembly and idler tension pulley i released tension on the drive belt removed the pulley from the assembly replaced it with the new pulley including the pressure washer which keeps the pulley stable realigned the belt and replaced the front cover and closed the top. done.

5 screws on back of control panel remove back cover pop off knob 1 screw pull switch out the back disconnect hose heres where I had a problem wires are # 1 2 3 on old and new switch 2 and 3 where reversed on the new switch if you turn on washer and it starts to agitate reverse two single wires I didn't try it until I had the back on so try it first

Changed the belt started working like new.

For the washer/Dryer combo, replacing water valve was easy, first you need to remove washer front panel and top lid, make sure that washer electrical is unplugged, turn off gas, turn off water valves.remove 1-screw holding water valve. reaching from top and using pliers remove retention clip holding hose. remove old water valve, there are two electrical connections for cold and hot water valves, make sure you mark them, remove them from old water valve. insert new water valve, connect hose and make sure that retaining clip is connected correctly.connect electrical wires. screw water valve into place from rear of washer. connect water hoses. before connecting panel and lid, turn on water valves and observe if there is any water leaks.

Took off back of washer. Control panel and top. Disconnected hot and cold water inlet hose. Pulled offwire leads. Unscrewed valve from washer. installed new valve. Reconnected wire leads. connected hoses. put top back on. put back of washer and control panel back on. Reconnected water. Done. Nothing too difficult. just a little time consuming. Space was an small issue in the laundry room.

my husband took off all the parts and put the new ones on in about 45 min only to find that the motor was burned out and the motor is discontinued but all the other parts are available!!!!!!!

It was easy. No problem getting the to v-belt.

The original inlet valve comes in from the rear and the replacement inlet valve mounts horizontally and this will not allow the use of the valve mounting plate and I needed to make a new plate so the supply hose could mount. After making the new plate and having the supply hose attach vertically, the system appears to be functioning properly. Having to make a new mounting plate was an unexpected adventure!

lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,

watched the video, all instructions were perfect!

The drive block spline was loose in the Agitator, for the now block to fit tight enough to stay in place while reassembly of the Agitator, ( keep falling out) the old block had to be driven out. Had to design a wire tool to hold the block in place until the Agitator could be fitted over the shaft and seated tight on the shaft drive, then pulled the wire out. Wasn't the most easy task to do and sure took more than 5 min. to install.

The part was fine,except for one problem. The screw holes in the part were too small for the sheet metal screws. After several minutes of trying to get the screws to turn, I got a small round file and enlarged the holes until the screws fit. Luckily for me, I've had to do things like that before. Otherwise, the installation was straightforward. And the washer no longer leaks!

This appliance is being used in a third world country with no parts access. I discovered Partselect and easily found the schematic with parts listed. Needed parts were easily identified ordered online and received within 4 days in the US and in time to take on my day later flight outbound. The process was seamless and expeditious. Thank you Partselect!

Checked drive belt by removing two screws on the BOTTOM of the front panel. Would spin dry but not agitate. Motor is two directional. Spin one way, agitate the other way. Same belt, so not the belt. Removed the agitator and the drive was turning but not the agitaor. It APPEARED that the agitator drive block was part of the agitator. IT IS NOT. Tap out the drive block,(Part # PSii52574)by threading a long bolt with the same threads as the screw that held the agitator to the drive assembly. Gently tap and the drive block will drop out. Replace the Agitator drive block. Worked like new for $21.32 + SH. The old agitator drive block was broken in pieces thus not allowing the agitator drive to turn the agitator back and forth. Did not need the Agitator, agitator screw or agitator spacer. Easy fix. No experience necessary. Cliff