WJSR2070B3CC General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dave from Irving, TX
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Washing machine flooding
The after school director told me of the washing machine flooding. It took only a bit to find the hose that was leaking--a little longer to figure out where it went. It was the bleach line to the drum from the little bowl under the lid. It had pulled off.
I noticed that three of the four tub dampening straps (little rubber bungees) were broken. PartsSelect had a good exploded view of the washer that helped me locate the correct part and order it. They were shipped quickly.
Start with the machine empty of water and unplugged.
The front of the washer pops off (most have a removable top but this GE did the front instead). This exposes two screws to remove in order to lift and remove the top, exposing the tub. While you lift the lid, you have to remove the bleach line from the pocket at the front of the machine. It helped to unplug the machine and remove the lid switch to make access easier. It has two screws holding the assembly to the lid.
The straps are on the four corners of the tub, attached by hex-head screws. The two in the back aren't as easy to access. A stubby nutdriver would have helped for the screws that were upside down holding the straps to the frame. The straps were replaced and all the parts put back.
The washer is quieter and shakes much less. It was ready for the Christmas dinner washing later in the week.
I noticed that three of the four tub dampening straps (little rubber bungees) were broken. PartsSelect had a good exploded view of the washer that helped me locate the correct part and order it. They were shipped quickly.
Start with the machine empty of water and unplugged.
The front of the washer pops off (most have a removable top but this GE did the front instead). This exposes two screws to remove in order to lift and remove the top, exposing the tub. While you lift the lid, you have to remove the bleach line from the pocket at the front of the machine. It helped to unplug the machine and remove the lid switch to make access easier. It has two screws holding the assembly to the lid.
The straps are on the four corners of the tub, attached by hex-head screws. The two in the back aren't as easy to access. A stubby nutdriver would have helped for the screws that were upside down holding the straps to the frame. The straps were replaced and all the parts put back.
The washer is quieter and shakes much less. It was ready for the Christmas dinner washing later in the week.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from West Columbia, SC
- Parts Used:
- WH41X10077
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Water Leaks
I pulled the top off of the washer and found that my leak was coming from a small hole in the hose and water inlet. I had to remove 2 small bolts and a hose clamp to remove the old part,I did the reverse to install new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Syracuse, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer wasnt draining properly, yet you could hear the pump turning.
Blowing hard into the drain hose would force the water off the impeller and allow the pump to reach proper speed to correctly drain. Start by unplugging the machine. To replace the pump, I simply removed the front cover of the washer. There are 2 clips to release along the top of the cover, then carefully pry forward and then lift it off the bottom clips. There are two wires which were a bit stubborn to remove. Carefully wiggle and pull with pliers, and be sure to note which one goes where. There were 2 bolts to attach the pump to the machine, which I removed using a 1/4" drive socket set, the size of the bolt head escapes me - on the small side anyhow. Also two squeeze clamps holding 2 hoses, which were easily removed using pliers. Pull the hoses and watch a pint to a quart of water dump out on the floor. Reverse the process to install. The hoses are tucked back in there, so you may want a flashlight to make sure you get the clamps back on correctly. Replace the front cover, and dont forget to plug the machine back in and you are ready to rock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from East Islip, NY
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer not draining the water
1- Shut off water and unplug unit
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out
15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out
15 minutes - 30 minutes tops!
Good luck Matt East Islip NY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelvin from Richland Hills, TX
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Washing machine quit pumpig the water out.
Removed the old one and installed the new pump, by removing the front cover and disconnect everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GABRIEL from COCOA, FL
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
the water, not get out (drain)
e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) that were easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from milford, PA
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer would not drain on any cycle
Use flat head screw driver to push in clips that hold on front panel.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
use plyers to remove hose clamps on motor and remove hoses.
use nut driver and remove two screws holding bracket in place. disconnect two wire plugs.
Install motor and work above in reverse.
very simple 15min job at most.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- REX from PLEASUREVILLE, KY
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
agitator couplier was stripped out on the shaft
I put my fingers under the agitator and pull up , this pulled it off the couplier, then I used a 11mm wrench to remove the bolt that holds the couplier in place and pulled the couplier off, the new couplier didnt arrive until after I went to work but my wife had it all back together when I got back home,I told her what to do and she said it only took about 10 mins. to get together, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from Brookville, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Clothes washer agitator stopped moving. Threads inside coupling were worn so badly the agitator was free moving.
***Partselect.com had my ordered part delivered within 3 days.*** First, I pulled up on agitator and removed it. Then, loosened bolt on coupling and removed it. Replaced with new coupling, placed and tightened new longer bolt that came with new coupling. Replaced agitator and started laundry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from ELVASTON, IL
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
On knob went bad
Took new one out of package, and push it on. 4 seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from SCOTTSDALE, AZ
- Parts Used:
- WH01X10060
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My dryer wouldn't start, I saw the part on your website after reading comments from other people
I put the nob on the post, one side is flat the rest of the lever on the dryer is round. So I matched up the lever with he inside of the new knob and slid it on . The dryer works perfectly. I ordered it on May 5 th and the nob arrived May 15 th. I guess Georgia is a long way from Arizona. But the part fit perfectly and I am happy. Thankyou.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- audrey from WHITING, NJ
- Parts Used:
- WH01X10106
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
dryer shut off and would not go back on
After much research I decided to have to repaired all new models were not good. Reached out to local service repair because I beleved that it was the timer. $270 for service call REALLY and $125 for part.
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY
Reached ot to PART SELECT LOVE YOU GUYS) SAID WHAT WAS THE PROBLEM the chocie was a new knob or replace timer. I am
83 yr old woman and believe I could have done it myself if it wasn't for the problem of moving the dryer out. shut off electric four screws
take out old replace new rewire the four screws WORKING NEPHEW
DID IT IN TEN MINUTES NO CHARGE BUT THANK YOU PART SELECT FOR REAFFIRMING MY DIAGNOSIS. AUDREY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from WEST CHESTER, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Stopped agitating
I was going to replace the washer. .. I am a cabinet maker and pretty good at what I do. I have to admit before seeing the video I was out of my comfort zone with this repair. I was shown not only the part needed and that you folks had the part in your inventory on hand. I was pleased to see how inexpensive it was $7.40. I had it shipped for $8.70. I ordered online at 2 pm. the part arrived the next day at 1 pm. AMAZING!. I spent ten minutes making the repair. The machine is now back to it's like new self! Regards, MichaelAndrews.biz
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from MONROEVILLE, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken start knob
Just push knob on less than 4 seconds
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from YARDLEY, PA
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken knob and could not turn on dryer
followed the video you provided and it was easy!
Was this instruction helpful to you?
Thank you for voting!