VWSR4160GW General Electric Washer - Instructions

After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.

Aside from getting the wet clothes and most of the water out,the toughest part of the job for me was to figure out how to get inside the machine. I nearly wrecked the thing trying to lift the top panel. After some frustration I removed the star-type screws on back of the control panel and found, tucked away neatly, the documentation/parts list complete with instructions on how to remove the FRONT panel. Once I got inside it was easy to locate the pump. I ran the drain cycle for a moment to see if the pump turned at all. The original had an exposed fan so it was easy to see that indeed the motor was not turning. I inspected all the hose and electrical connections to make sure I had the tools I'd need and the savvy to replace the part(s) if I could locate them. I'm not much of a web-head, so I was a little surprised when I typed G.E. appliances and the search took me to partselect.com where I was pretty much coached through the procedure before I even ordered the part. The box arrived ahead of schedule (yay) and when I looked at the pump it didn't look much like the one I was replacing. But then I realized it was the same thing just ten years more advanced. I used a small pair of vise grips to pinch and lock the pipe clamps open. I know there is a plier made for this, but... Anyways, after loosening the clamps and sliding them away from the pump I pulled the hoses off and let the last of the rinse water still in them run down my shirt sleeve to my elbow. (optional, not recommended) Thus refreshed I then rummaged through my socket set and found what I needed to remove the 2 sheet metal mounting screws and disconnected the 2 power leads. I removed the faulty pump and proudly showed it to my wife. Unimpressed, she asked how much longer. I quickly reversed the procedure to install the new unit and confidently piled in a load of laundry. The cycle completed just fine and has done so since. I will and have recommmended partselect.com to friends and will use it again for sure.

To diagnose, first I unhooked the washer: power, water supply, and drain pipe. I then slid the washer out, laying it on its front. With nutdriver, I unscrewed two screws that held the other end of the drain tube and removed it completely. Then, again with the nutdriver removed 4 screws from the back near the legs, two in between the legs in the middle, and approx. 4 to 6 on the bottom. This let me pull the bottom off partially to access the motor area. (I did did not take the bottom completely off, only about 2/3 off and let it bend over, as it was flexible tin) The belt was broken. After receiving the new belt, I positioned it between the pulley and the motor and between the drum and the big pulley. Then I rotated the big pulley, pulling the belt onto it as I rotated. At the same time, as I rotated, I pulled the other end of the belt on to the little pulley. Once it was on, I would put pressure on it as I turned the pulley, to jump the belt to the appropriate grooves on the little pulley. Note: the replacement belt had been modified, so it had one less groove than the pulley. I would have known this if I had read the insert that came with the belt first! Anyway, this was not a problem, only a design change. Also it was important to start the belt on the inside, so if it slipped, you didnt loose your bite. Total diagnostic, repair, and reassembly time: 30 minutes plus or minus. I had read other online forums that said you had to loosen the motor, etc. And I do know some type of a belt installation tool was offered on line, but I got along fine with my installation method. An extra set of hands would have been helpful, but not necessary.

Simply put hands, one under each side of the agitaror and pulled up. The part snapped off very easily. I then placed the new part in the tub and pressed down. Extremely easy, should have done it sooner!

First I removed the front panel by prying it forward with a Screw driver away from the side panels at the top (wrap a shop rag around the Screw driver to keep from scratching the paint). Once you have the panel pried loose at the top ... lean it forward until you can lift it off the tab type hooks at the bottom.
I next unplugged the wires from the motor. The orginal motor had three wires ... two on top and one on the left side. The one on the side is a ground wire for the open frame motor. The replacement motor is sealed and does not require this wire. Just leave it unplugged when the new one is installed.
Next I removed the inlet hose that attaches to the back of the pump. Remove it by loosening the hose clamp and removing it from the bottom of the tub, leaving it attached to the back of the pump. It is much easier to remove and transfer to the new pump once it is out rather than fight with the spring type clamp on the back of the pump in the close quarters inside the machine.
Next I removed the outlet hose from the top of the pump. Squeeze the spring clamp with Pliers and work it up and off the pump.
Now I just used a Socket to remove the two bolts holding the bracket to the inside front of the machine and removed the assembly.
I now removed the inlet hose from the back of the old pump. Just squeeze the spring clamp with Pliers and work it up the hose and off the pump. Transfer the hose to the back of the new pump reusing the same clamp.
I now bolted the assembly back into the machine, reattached the outlet hose to the pump, and then reattached inlet hose to the bottom of the tub. All that was left to do was plug in the two wires to the top front of the pump motor (as I mentioned earlier, leave the side wire from the old pump unplugged as it is not needed on the new one). I then ran the machine for a few moments with the front off to check for any leaks and then put the front panel back on.
The whole replacement cost about $50 and took barely 15 min. from start to finish. The machine now works perfectly.

I figured out that fuse link was open.Upon receipt of fuse link I ordered and replaced the bad fuse link hidden on wrapped electrical harness leading to the motor inverter board connector, BINGO... My washer works and I enjoy my washing machine again.My thanks and appreciation to partselect.com for the help & info you rendered to me.

Replaced inline fuse, simple fix.. but didn't work, checked lid panel switch which was working fine. Still no motor action, followed the reset procedure, and then watched above the motor for error lights, just below the drip cover, nothing, no error blinking code. Not sure why the kit contained two fuses, there is only one in our washer. So, my testing is over, in the error code, it stated if no blinking light, the failure is most likely a motor, I was hoping for something else, from switches to fuses. I reviewed the wiring diagram looking for an addition fuse link, found nothing.. The washer is four years old looks great, but now worthless, the replace motor for the unit is something like #300.00 with shipping. You can't test the motor, so it is a shot in the dark if you replace it. Really disappointed with GE's engineering and poor quality of manufacturing, and the lack of info to test the unit. We live on an Island, so not easy to find a local repair person. Your parts replacement service was fast and easy to use. But so much for GE washer.

removed hoses and clamps. removed 2 bolts on pump. put it back together. done 15 min.

Used 1" puddy knife to depress spring loaded retainer tabs. Front panel is removed by prying the top of the front panel away from the machine. Lift front panel to release bottom from machine. Set panel aside. New belt is installed by placing it on the drive pulley and then rolling belt onto the motor pulley. Rotate the motor by hand while moving belt so it is properly seated on pulley.

First I removed the dials and the cover, removed the one screw that held the timer in place, disconnected the wireing harness and pluged it into the new timer set it in place and replaced the screw that held it in place,replace cover and dials. [ anyone could do it. ] Thanks,Tommy

Removed front cover, lifted lid. Unnapped the broken tub cover pulling the tub forward to allow the old cover to clear the rear of the housing/top. Installed the new tub cover by once again doing the same thing and carefully snapping it into place. Reconnected the rubber sping offloads, lowered the top and reinstalled the front cover..ready to run.

I used a butter knife to pop plastic clips that hold the front panel to the top panel, one clip on each side of front cover. I never thought the new belt was going to fit, it barely fit on the big pulley, much less around the small pulley too. It needs to be stretched a lot to get it on.. but it will fit :)

I used needle-nose pliers to remove the lock tab and , in seconds, I replaced the knob !!!

1) Disconnect power
2)remove front panel
3) remove screws and take hoses off
4) remove & replace water pump
:) YAY. all done

I wasn't sure that a new knob/clip would fix problem b/c shaft wouldn't turn with pliers. But knob was so inexpensive I wanted to try it first. I received the new knob/clip and the dryer worked perfectly; the knob had been broken for a year before it had quit working entirely. Don't let someone tell you that you need a whole new timer before you try the new knob/clip. Still working perfectly and I'm so pleased. And my part arrived within 2 days-wonderful!