WCRD2050FW General Electric Washer - Instructions

Our GE washer stopped agitating. We bought us a Whirlpool Cabrio washer with auto-sensing and an impeller instead of an agitator. My wife couldn't get used to washing clothes with so little water. We found out about PartSelect.com and ordered the part they indicated would probably fix our GE washer ($5.86) - the Agitator Coupling Kit. Ordered it on Friday, received it by Fed Ex the following Tuesday. It was an easy installation. Our GE is working fine. Took the Whirlpool back to the store, got our $637.00 back.I plan to use PartSelect.com again,if I need to. We don't like the new type washers as well as our 7-1/2 year old GE.

First I located the trouble. I noticed that it was water leaking and figured it had to be a hose. I took the front panel off of the washer and after noticing that the drain hose had a slight hole in it, realized that I could fix it and save myself a repair call. I undid the two hose clamps and removed the hose. I went to a local repair shop that could not guarantee the right part. I went online and found Parts Select.com. I entered minimal information and the picture of the item that I was looking for, the Drain Inlet Hose, was staring at me! Within 3 business days and less than 20 dollars spent, I repaired my washing machine. The total time spent to repair after I received the hose took about 10 minutes. I will definitely use parts select .com and recommend to all my friends and family. Thank you.

I had help taking off the old parts,coupling was not easy. But I installed the new parts by my self and I'm 74 years had trouble getting the Agitator Coupling back on, But the straps were easy, Any way I'm back to washing again thanks a bunch

I bought 3 parts for I didn't know what I need so I listen to the companies video twice.
I popped off the agitator which was easy. then had a little trouble with getting the screw/nut out it was rusty. Finally got that off then I worked backwards and I found I didn't need all the parts which I sent back with no problems. My machine works as good as new ,it has stopped making noise. I am really proud I did this by myself and didn't need my husbands help,

I also spent less than 12.00 to fix and a new one is over 600.00.

Thank You
Christine brooks

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

I removed agitator by pulling it up until it unsnaped.

I removed the old agitator coupling by removing the bolt and pulling up while twisting it.

The new coupling looks different than the old part but fits the same.

I pressed the new coupler on to the agitator shaft, reinstalled bolt and pressed agitator on the agitator coupler until it snaped into place.

Washer runs like new!

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.

I pulled on the bottom edges of the agitator, like the video said, until my fingers were numb. Finally, after I got aggravated, I beat the old agitator into a hundred pieces with a hammer and chisel. Then I slid the new agitator into place and gently tapped on the top of it. It snapped into place and has worked like a new one every since.

Removed the back of the machine and then flipped the machine on the side and loosened the motor to get the old belt off. A piece came out so we had to check the schematics online to figure out where it went. We believe it was the out-of-balance cut off switch. So to fix that we unplugged the motor assembly and took it out. I also had to fish the spring out of the vacuum, no small task. The worst part was that the belt was so deteriorated that it was super greasy and the carpet ended up a mess. We replaced the motor and belt and now it actually gets the water out of the clothes. Simply Green cleaner was used for the rug and after some strong elbow grease it was cleaned. If not for the mess and the other part and the vacuum snafu, I would have labeled this as easy.

The repair went just like the video! Easier than I would've hoped.

Watched the video, good video. But instead of taking the bolts out first, it's easier to remove bolts last, to give support to remove the hoses.

1. take the machine apart, since the noise comes when the barrel is spining, I just watch for anything that contact to the axel.
2. without special tools, it was difficult to take off agigator, and a nut (that tighthened lefthanded).
3. Once defect part found, seach online for the part supply to replace.

First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything back together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.

I ordered the part on Wednesday didn't think we would be washing any clothes until atleast Monday. The pump came on Friday! Installed it 15-25 minutes(that's taking out the old one too) . As someone stated before the only (little) problem was the spring clamps. Screw the pump in first and then put the Clamps on.

I removed the agitator by simply pulling up. I then removed one bolt to get the agitator coupler off. I installed the new coupler, replaced the bolt and slid the agitator back down.