S1070A5WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Justin from New Orleans, LA
- Parts Used:
- WH49X10042, WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Agitator not working
I just added the agitator coupling and screwed it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucas from hastings, MI
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
washer would not agitate
The part came very fast and was easy to install, I pulled off the agitator and removed one bolt, replaced worn out part with new part and put the new bolt that came with the part in. Reatached the agitator and washed some clothes. done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Puyallup, WA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator did not rotate
1. Remove agitator with a quick upward jolt.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.
2. Remove bolt with ratchet or wrench.
3. Remove agitator coupling.
4. Install new coupling, tighten new bolt and slide agitator down until it latches after aligning appropriately.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FERNANDO from ALAMOGORDO, NM
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
The agitator would spin freely by hand.
I first placed a rope under the fins of the agitator and used a 2X4 board to pull up the agitator which needed very little force to release itself from the agitator coupling. I removed the nut holding the agitator coupling, removed the stripped agitator coupling. Installation was just the reverse process, inserted the new agitator coupling, placed and tightened the screw, and pressed down the agitator over the agitator coupling and I was done. Over time for the repair was between 5 and 10 minutes, very easy, and I have no experience repairing washing machines.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- akram from lakewood, OH
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
the washer would work but the agitator wouldnt spin
took out the agitator then removed the agitator coupli and found out that the coupli was worn out, i then replaced it and everything worked again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- REX from PLEASUREVILLE, KY
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
agitator couplier was stripped out on the shaft
I put my fingers under the agitator and pull up , this pulled it off the couplier, then I used a 11mm wrench to remove the bolt that holds the couplier in place and pulled the couplier off, the new couplier didnt arrive until after I went to work but my wife had it all back together when I got back home,I told her what to do and she said it only took about 10 mins. to get together, very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from Waynesburg, PA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Washer would not agitate
We removed the agitator then the bolt holding couplier. The inside of the plastic couplier had stripped after 5 years. We cleaned around the metal part of the agitator then installed the new GE plastic couplier, put in the bolt & replaced the agitator. The machine works better than ever.
The GE website said this part had to be replaced by a certified technician. The estimated service call alone was $80 & the part was not available from the GE website.
The GE website said this part had to be replaced by a certified technician. The estimated service call alone was $80 & the part was not available from the GE website.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debbie from Riverbank, CA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator was no longer moving
I am a mother of 3 so a washing machine is vital. I called various appliance repair places and was quoted anywhere from $50 - $85 just to come and look at it. I did some online research and discovered that the part itself was less than $7. After paying for 2-day shipping, my total was under $20. I thought, what do I have to lose. I received the coupling kit and read the EASY instructions. I had already removed the old one so by the time I received the new one, it took me less than 10 minutes. WOW!! I now have a working washer!! .THINK AGAIN!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rob from Wytheville, VA
- Parts Used:
- WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
Agitator Not Working
I removed the center piece in the washer by pulling up on it, removed the retaining bolt and the agitator coupling.
Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.
I never would have though about it until I searched the problem on line. I had already decided that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.
PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.
Installation reverse of removal...no problems. The spline on the inside of the agitator coupling was worn out.
I never would have though about it until I searched the problem on line. I had already decided that I would have to buy a new washer (again)...I had a pressure switch problem about 6 months ago.
PartSelect is great...I ordered the parts for both problems from them and I have kept my old washer alive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joel from mt vernon, IL
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
two tub dampening straps snapped
I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Edina, MO
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
washing machine quit agitating
took the two screws that holds the instrument selections off retreived the directions from inside this panel and followed directions step by step and removed the spline that makes the machine agitate, seen that the inside of the spline was smooth, ordered part and reversed operation in putting it back together.
p.s. make sure the refill shutoff hose is connected as we had forgot to do this and we ran water on the floor, had to take back apart and re-connect thehose .
ordering the part and fixing it myself with my sons help saved me a repair bill which I am sure would have cost me at least $75.00 more.
p.s. make sure the refill shutoff hose is connected as we had forgot to do this and we ran water on the floor, had to take back apart and re-connect thehose .
ordering the part and fixing it myself with my sons help saved me a repair bill which I am sure would have cost me at least $75.00 more.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Silver Spring, MD
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer not empyting
Removed front cover, disconnected wires and hoses, reversed process
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leisha from Trinity, NC
- Parts Used:
- WH49X10042
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Washer would fill and drain, but not agitate the clothes, I kept getting a pile of laundry soap in the bottom of the washer and left with dirty clothes
Removed the screws, pulled out the tall skinny thing that rotates, pulled out the broken part, ordered the new one, replaced it, (you have to push down until it snaps into place) Put everything back together and had clean laundry within 45 minutes. Anyone can replace this part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marci from Salt Lake City, UT
- Parts Used:
- WH49X10042
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
GE Profile Washer would not agitate but would still spin, etc.
I used the "belt" technique to remove the agitator. It was difficult at first to remove but after a few tugs on the belts that were looped under the plastic bottom, the agitator came up. Then I unscrewed the bolt holding the coupler. The agitator coupler kit purchased from PartSelect came with a new screw so I replaced the old coupler with the new one and fitted the new screw in it's place. I put the agitator dasher back on and then it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from ORO VALLEY, AZ
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken straps
replaces as per video. Very helpful
Was this instruction helpful to you?
Thank you for voting!