WPRB9220DW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kiel from Laughlin AFB, TX
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Washing Machine Leaky Hose
I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Merced, CA
- Parts Used:
- WH41X10096, WH16X513
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drain hose replacement
Put the drain hose clip on (it will take squeezing but the hose will pass through). There will be a groove that whose width spacing is similar to the clip. Once that's on, insert hose and screw in the clip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma from Holiday, FL
- Parts Used:
- WH43X139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
There was no fabric softener dispenser
Opened lid and place on agitator ... finished
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Ridgewood, NJ
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Wife noticed water pooling around the washing machine
Unplug the washing machine. There are electrical components that can injure or kill you. Using a screw driver inserted just below the lid of the washer in the front, there are two (2) spring clips that you push on to release. Then the front of the washer tilts down and you remove it and set aside.
On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.
On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Concord, CA
- Parts Used:
- WH41X10096, WH16X513
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
the hose extension had a tear
First I removed the screws that held the drain hose clip to the washer. Then I pulled the hose, along with the clip, completely out of the washer. I then took the old hose out of the washer clip and put the new hose in the new clip; I pushed the hose into the washing maching and tightened the hose clip to the maching with the existing screws. Seriously easy, took less than 15 minutes. And I have virtually no handyman skills at all!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Herrin, IL
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Pump was making grinding noise
Popped off the front of the washer, removed old pump by disconnecting 2 hoses, 2 screws and power. Pump new pump in, reconnected everything. Done. Quite possibly the easiest repair ever!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Troy from FARGO, ND
- Parts Used:
- WH13X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Continuous water running during spin and rinse cycle
Turned off the water and disconnected the water lines. Took of the control panal, only 4 screws and got access to the dual inlet water valve. Device removes with 2 screws and power connectors slide off. Reverse removal and your in business. So easy to do, part was an exact fit. Don't buy a new washer, fix your old one!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from ST PETERSBURG, FL
- Parts Used:
- WH1X2026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench set
Washer would pump but not spin.
Viewed video on installation of new belt. A little awkward to get to the rear bolts, but used a wrench with success. Now washer spins correctly. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Renaldo from S PORTLAND, ME
- Parts Used:
- WH43X10034, WH49X10042
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator not rotating properly. The dogs were worn and are non replaceable
Very easy just pull straight up on agitator and remove bolt on coupler. Install new coupler and line up agitator and push down. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Chimayo, NM
- Parts Used:
- WH43X10034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The agitator "wings" are open at the bottom so any clothes with strings gets caught in these wings and eventually brake the wings off.
I watched the video provided by your site and followed it. I removed the clothes softener part from the agitator, Got a good grip on the agitator and pulled up. It came right off. Aligned the new agitator groves and slid it into place, put the fabric softener part back on! Super easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shaobo from fremont, CA
- Parts Used:
- WH02X10265, WH2X1199, WH02X10383
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
washer barral spins with loud noise, turned out to be the worn Wahser Hub
1. take the machine apart, since the noise comes when the barrel is spining, I just watch for anything that contact to the axel.
2. without special tools, it was difficult to take off agigator, and a nut (that tighthened lefthanded).
3. Once defect part found, seach online for the part supply to replace.
2. without special tools, it was difficult to take off agigator, and a nut (that tighthened lefthanded).
3. Once defect part found, seach online for the part supply to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Mendota, IL
- Parts Used:
- WH02X10383, WH02X10265, WH2X1198
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
loud squeal on spin cycle Bad tub bearing.
First buy the tub nut wrench. I can't over emphasize that! $12 at amazon. With out it getting the inner tub out will be the worst part of the job. And you will have to buy a new nut. I had trouble getting the old bearing out of the outer tub. I had to drive it out with a punch. The only other problem I had was after getting everything back together the new tub seal leaked. When I installed it if fit very loose on the OD. I ordered a new seal hoping it would fit tighter but it didn't so I coated the the seat of the tub and the OD of the seal with gasket shellac. That solved the problem. Working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nolan from Fort Polk, LA
- Parts Used:
- WH41X22935, WH41X10096, WH16X513
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Water was leaking from the tub to the floor.
First I removed the two clamps that hold the inlet drain hose onto the pump. **There may still be water in the hose** This was pretty easy, but a set of vice grips would have been nice. The space is not too cramped, but required a little bit of wiggling. Putting it on was a little bit harder, just because I did not want to tear the hose on the tub or pump inlet. Make sure both are fully seated or else it could still leak. The drain hose and the clip are pretty self explanatory. I tried to buy a generic drain hose at a big box lumber yard, but I could never make it fit right.
Hope this helps.
Hope this helps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Perrysville, IN
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken straps
replaced them & working fine now....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angela from Manti, UT
- Parts Used:
- WH23X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The pump was easy to put on the the washer still doesn't work . The water still just drains out.
First I took the bottom of the washer off so that I could get to the pump then I took a socket set to take the pump off. Then I put the new pump on and put the bottom of the washer back together.
Was this instruction helpful to you?
Thank you for voting!