WNSE4200A0WW General Electric Washer - Instructions

Replaced the plastic agitator coupler

figerout how to take the old one off that was a little hard to do but did it. got the socket set to get the middle undone. clean to out and put the new one in and it works just fine and better then ever.

REMOVED THE AGITATOR BY LIFTING STRAIGHT UP WITH MY HANDS. COULDN'T REMOVE THE COUPLING WITH THE NUTDRIVER AT FIRST, DUE TO RUST. SPRAYED A LITTLE WD40. LET IT SET FOR FIVE MINUTES AND REMOVED THE SCREW VERY EASY WITH THE PLIERS. TOOK OUT THE OLD COUPLING AND REPLACED IT WITH THE NEW ONE. THANKS FOR THE YOU-TUBE INFO.

I followed instructional video on partselect.com, it was very easy, but it didn't take care of the problem. I got to to order "TRIPLE WATER VALVE" and that did the trick. After opening the washer first time (for water fill nozzle), it took me even less time. You don't have to take the front panel off to replace the water valve.

pulled front panel off it snaps in but had to get off. then remove two bolts holding too down. moved top around to get to straps. front to easy 5/16 deep socket aND rather .the other end has 1/4 socket back hard to get too not bad. took 30 minutes. didn't fix problem. on bottom of motor looks like it had rubber bumpers but none there didn't find any on parts list. went to parts house auto got two rubber freeze plugs installed them in hole on bottom of motor that stopped the noise and rube moves very little now. also install new belt . install it put it on motor then on part of pulley then roll pull while keeping belt on motor roll pulley around till belt on all the way then roll pull more pushing on belt on motor till belt fit in all groves then roll it couple more times it will line groves up on pull. install top back down then snap front panel it your done.

My rubber start button gave out after 10+ years...kept getting stuck inward and was unreliable. I thought about buying a new washer but my old one still works fine and the new ones are super expensive! My wife and I only do a couple of loads per week so decided to try to fix it ourselves.

Ordered a new one from this site. Was about $20.00 for the new button, but I have not spent a dime in over 10 years! I just cannot believe how easy it is to find the part and place an order. All you really need to do is to find the tag on the washer with the model number. What a fantastic business and website!

The install was easy...pulled out the old one using a pair of needle nose pliers (still useable in an emergency) and installed the new one. I was smart enough to coat the new one with a little Vaseline and it slipped (wiggled) right into place. For the record, the washer works just fine without the button too.

Glad I tried to fix it. Would have cost me a couple hundred bucks for a professional repair.

Good work ! PERFECT!

Watch the videos you might be a little skeptical at first. I watched the videos about 8-10 times before I bought the part so I took my part out first then got back on you tube watched a few more videos and got on parts select website found the part matched it up to what I pulled out of my washer ordered it got to me in a weeks time put it in and working like new again cost about 14.00 shipping and part together saved about 200.00 per my estimate I had to fix it.

Removed the front cover with a screwdriver, by locating and slightly prying the metal clpis back to release the cover. Then I removed one screw (only one visible) from the strap that hold the top cover/lid down. With a little prying, I lifted the lid up out of the way, and suspended it with a cord. I removed the old dampener straps and replaced each one at a time with the new strap. It was not to hard to get to the screws (I have large arms), and it only took me nearly a half hour to complete the task. It would have been easier if I used two different size nutdrivers, but it was easy enough with an adjustable wrench. Then simply put everything back to together in reverse order of how I took it apart. The wife was impress that I fixed another thing around the house.

First I removed the front cover, Drained out water by hand, Romoved two drain hoses going into old pump,removed the electric very easy it was two wires,installed new pump and reconected all. Now my wife is happy again and so am i. Your installation video was the KEY to my success.

Removed the two hex head screws from the broken strap and replaced it with the new one. The other three straps were not broken but I also replaced them, again, one at a time. This made sense,since the machine was at least ten years old.

I had to replace the water fill nozzle on my GE washer, and having the instruction video on the parts page is a real time-saver. It shows how to remove each part on your washer in order to access the area where the part needs to be replaced. Start to finish, about 20 minutes. Easy peasy.

Wife put on the new part and she used a pair of plires and it was a little difficult to get her hand in the tiny spot but she put it on in less than 15 minuets and it is working great.

1- Shut off water and unplug unit
2- Wedge flat head screwdriver in between front panel and side panel of washer and remove the front. (1 minute)
3- Get a towel and a bucket (if you still have water in it) and drain remaining water from back of washer first... Then be prepared for about 20oz more of water when disconnecting the old pump. (5 minutes)
4- disconnect old pump it will look slightly different then the one you bought! (3 minutes)
5- re attach new pump with the same hose clamps and reattach the front panel (5 minutes)
6- fill it with some water/ spin it out

15 minutes - 30 minutes tops!
Good luck Matt East Islip NY

Removed the old one and installed the new pump, by removing the front cover and disconnect everything.

First I found out on the web how to open the washer's front cover.
For the strap in the front, it's relatively easy to replace a strep if your hands are somewhat flexible.
For the one in the back, I also needed to open the top dial panel, in order to lift the main lid connected to it, in order to then be able to reach one of the screws of the back strap. the other one of its screws I was able to reach from the front with a ratchet and extension from the front. Arms do get heavy from time to time, but overall it was manageable.