WISR106DTBWW General Electric Washer - Instructions

The hardest part is lifting the washer to get a the bottom. Disconnect the power, shut off water. Disconnect hoses and drain hose. Move washer from the wall about 2 feet. Tilt up front of washer. I used 4 12" long 8x8 inch lumber, lift washer….place one on each from corner. Lift again, place 1 more 4x4 on each existing 4x4. Now remove the belt off the 3 pulleys. Use the flat blade screw driver to remove the C clip holding the Pully on the shaft, with the flat bladed screw driver and hammer. Once the C clip is off remove the metal washer, pulley, plastic lock (apart of the bottom of the pulley & the thrush bearing and it's washer. Using the parts supplied (the "new thrush bearing is a bearing and washer combined) replace as you removed it. Thrust bearing, pulley, washer and, c clip. I tapped mine on using the flat bladed screw drive……becareful not to break it (they did supply 2 for me in the repair packet) make sure he c clip is secured. Lower the washer after removing all the tools from under the washer, by reversing the lift sequence. Slide the washer in place. Connect the hoses back up. Plug it in.Reconnect the drain hose, you should be good to go.

pulled front panel off it snaps in but had to get off. then remove two bolts holding too down. moved top around to get to straps. front to easy 5/16 deep socket aND rather .the other end has 1/4 socket back hard to get too not bad. took 30 minutes. didn't fix problem. on bottom of motor looks like it had rubber bumpers but none there didn't find any on parts list. went to parts house auto got two rubber freeze plugs installed them in hole on bottom of motor that stopped the noise and rube moves very little now. also install new belt . install it put it on motor then on part of pulley then roll pull while keeping belt on motor roll pulley around till belt on all the way then roll pull more pushing on belt on motor till belt fit in all groves then roll it couple more times it will line groves up on pull. install top back down then snap front panel it your done.

Pull hose out from wall and drain water into bucket. Remove two screws from back of washer holding on the clip. Pull hose out from washer its in there about 3 inches or so . If you order a new clip will make this even easier it's only $3.87 and I didn't realize I needed it. So, I just cut the old hose with a small saw near the clip so I could remove it and reuse it. Just slide the clip onto the end of the new hose - it fits into one of the grooves-I just made a note of where that was before removing from old hose. Then replace the two screws on the clip going to the back of washer. Put other end of hose into pipe in wall.

Pull off the agitator. Remove 1 bolt on coupler pull off coupler. Slide new coupler onto spindle. Replace bolt. Line up and slide on agitator. Seat it firmly in place. Done. Took all of 2 minutes.

(As I am an older female, I used YouTube to review the repair before trying it. YouTube scared me, the actual repair was much easier) I removed the agitator from the washer which revealed the agitator assembly held in place by a bolt. After removing the bolt, the assembly was lifted off the spindle. I cleaned the grime off the agitator, the spindle and the bottom of the washer basket. New agitator assembly was placed onto the spindle and pushed down. There was a distinctive click when it slid into place. I replaced the bolt to the top of the assembly. tightened it down, then slid the agitator over the assembly, matching grooves to teeth until that also slid into place with a click. It honestly took me longer to clean the grime than to change the part. Agitator is working perfectly

I ordered a selector knob and it was delivered in a short amount of time. I wasn't sure if it was the right one when I ordered it, but my husband just put it right on the dryer. He said it was perfect. Thank you PartSelect!

First removed tub comming from Tub and removed srcew to replace. Has to twist part out of slot to remove installed in reversed order. Really easy to do.

I had already removed the old coupling by removing pulling the agitator straight up off the coupling, then I removed the bolt that held the coupling in, and pulled the coupling up off the shaft.
I placed the new coupling on the shaft and pushed it down until it seated, put in the new bolt that came with the coupling, replaced the agitator, and was washing clothes within 10 minutes.
On time delivery, right part, complete with instructions.
Good job.

Surprisingly easy. I took the screws off, then pulled off the drain hose. I then inserted the new hose, and put back the screws. Amazing quick!

Replaced the plastic agitator coupler

figerout how to take the old one off that was a little hard to do but did it. got the socket set to get the middle undone. clean to out and put the new one in and it works just fine and better then ever.

After finding a matching knob for the broken one on my dryer, I ordered it from this website and within days had my dryer working like new again. Just slipped it on and that was it. No more using pliers to start the dryer. Couldn't have been easier.

Easy. Pulled off old one slipped on new one!

Pulled the old knod off and put the new knob on.

Ordered new knob from you people and simply replaced borken knob.