MNSR1090H5WW General Electric Washer - Instructions

I pulled agitator off revealing rotted hub. Had to remove inner basin from machine. This required pulling off top and tying up to be out off way . I had to get the control panel out of way. Removed back screws and moved it up as though hinged. I had to remove the water fill piece, as this was impeding removal of basin. I had to remove top ring off of inner drum. Needed a second person to hold control panel away as I removed drum. Once drum was out, it was an easy task to replace the rotted hub. I then needed to get the portion that was rotted and still on drive out. Could not wrench the hub nut out due to lack of leverage. Split nut with a chisel. Once old nut out, I cleaned up threads, put inner basin back in, again utilizing assistance in holding control panel out of way. Reinstalled in order. Before I had gone too far, I found that a six pronged jumper had fallen off of the controls. Found where it had been and re-installed. Put remainder back in reverse order. Machine back on line, and working properly.

Open back cover and found that drain pump had a bad seal. Took it apart and bought new seal some what same size. Put everything togather and start washing clothers and wife complained that it became wost the before. When on line and found pump and price was just right to take a risk. Ordered on sunday and got ups tuesday.
Replaced pump on Sunday and leak was gone and wife was happy.

------Got chicken and beer that Sunday--------------

Should be noted that the basket must be rotated on installation to find the best balance point!

removed washer front panel, top panel to access the water fill spout and hose. Disconnected and replaced.
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.

turned washer on side to get at the bolts holding motor. loosen bolts. remove flexable basket for water pump or one end of it. slide motor to loosen belt. remove and replace belt. use large screwdriver on motor to hold tension on belt while tightening nuts. hardest part was getting clamps back on the rubber basket.

I noticed the belt was off, first, then pulled it back on. Washer worked, but very noisily, as belt continued slippage. I bought new belt after reading how to repair, then when it arrived, I read how someone installed it without having to remove bolt, etc. I tried and succeeded. It agitates just fine, but stalls when spinning. It's like the belt is too tight, now. i am gonna try rotating the rotating parts to see if that will help loosen it.

After reading all the repair info and reviewing the diagram for my wash machine on this website I was ready to tear into my washer. I removed the front panel and lid to access the tub, pulled out the plastic agitator and revealed the broken inner base hub. The base hub was cracked half way around causing the inner tub to drop down and drag on the outer tub, making the washer sound like it was coming through the wall on a spin cycle. I then unbolted the plastic cap and removed it revealing the hub nut. The most valuable piece of advice in the repair info was abouthe hub nut being a laft hand thread (clockwise to loosen)and that it was on really tight and hard to remove. I put a short 8" pipe wrench on it, because of the lack of clearance in the tub, and hit it with the handle of a all steel hammer to break it loose. Unbolted the balancing straps (4) on the plastic top rim cap that holds the tub in place, unsnapped and removed it, then carefully pulled out the tub. I also had to unscrew the the control panel to reveal and remove the 4 screws holding the fill tube brace so I could push it back to remove the tub. I then took the inner tub outside and took it apart, 3 parts. The top plastic rim, the tub, and the broken base hub that are held together with torx screws. Then it was cleanup time, very dirty on the inside, used a garden hose, scrub brush, sponge, and soap. Cleaned up the hub nut threads with a wire brush and then the outer tub withe a sponge and shop vac. When the base hub broke it caused the inner tub and outer tub to rub together making a groove and plastic shards on the bottom of the outer tub that I had to scrape and sand smooth. A shop vac an absolute necessity in getting all the grime and plastic crumbs out of the outer tub so they don't get in and clog the pump. I received the replacement parts in 2 days! Reassembled in reverse order and everything worked great! Not a bad project at all when you know what to expect, thanks to Part Select.com.

Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry to wash :-)

Took complete tub assembly out of washer and inspected it. Did not find an obvious cause of leak but all 8 screws on inner tub hub were loose. As both tub nut and split ring were corroded, replaced them and the outer tub seal. Did a lot of cleaning!! As I was putting the trans assy back on the outer tub, I noticed a crack around the drain spout. At 1st, it looked like it belonged there but a closer look proved it didn't. I ordered a new outer tub (which came in 2 days) and I put the whole thing back together. Reassembly was far easier than disassembly was and I learned a whole lot about washers. YouTube is a great source of information.

I had no difficulty dismantling the washer until I got to the hub nut. It was frozen to the cone shaped fitting it was resting in. I had to take a drill and a 3/16" drill bit and drill the flange of the hub nut and then take a chisel and break it off piece by piece. Once that was off, I lifted the tub out and tried to pry off the split ring under the tub and it too was corroded and broke when I tried to pull it off. So I would advise you to buy a hub nut and a split ring if you are replacing the tub bearing, just to be safe. I went to an appliance parts store here in town and bought them. When reassembling the tub, I couldn't get a wrench or pliers on the hub nut to get enough torque to tighten it securely. And since I didn't want to spend $43 to buy a spanner wrench for a one time repair, I went to Harbor Freight and bought a $15 dollar adjustable wrench and cut 3 1/2" off the handle so it would lay flat to the tub and used a hammer to tap on the handle to tighten it securely. If you do not find some way to tighten the tub securely, it will come loose in the spin cycle like it did on me twice before I purchased the adjustable wrench and modified it to work. Plus I still have a useable adjustable wrench. Additionally, I took the washer cabinet, the tub and the tub sleeve and power washed it to get years of grime off of it. The washer now operates like new, saving me hundreds of dollars.

Repair went good, only wish i had bought a new tub seal, washer, an split ring....but i managed to save the original ones an it seems to be working like new again! thanks Partselect!!!!

Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.

Took about 10 Minutes to have my washer up and running again. So easy, and I almost bought a new washer! Fixed it before my husband got home from work. Thank you PartSelect!

I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.

Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.

First I removed the front panel using the screw driver. I removed the old belt which was in the bottom of the washer. I placed the new belt on the motor and adjusted the pullies. I replaced the front panel. The washer spins much better now than it had for the past year.