Models > WSM27TCBWWW > Instructions

WSM27TCBWWW General Electric Washer - Instructions

Jump to:

All Instructions for the WSM27TCBWWW
121 - 135 of 163
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Les from Anderson, SC
Parts Used:
5303937139
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Drum noise
Disconnected and moved the unit outside, just to clean the lint out of it. Removed the top, then two screws holding the front panel on. Disconnected the two door switch wires. Peeled off the old upper seal and cleaned surface with wire brush. Applied the supplied glue and clamped the new drum guide in place. While it was setting up, I cleaned out the entire inside of the dryer to eliminate the old trapped lint. Replaced the front panel and mounting screws. Reattached the wires and closed the top. Relocated back inside and plugged it in and reconnected the vent tube. Turned it on and it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gregory from Piscataway, NJ
Parts Used:
131862900
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Replace belt
Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Sunrise, FL
Parts Used:
WE03X29897
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Dryer would not tumble - heat but no drum rotation
Watch the video on how to replace the belt on PartSelct site belt installation page.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Mitchell, SD
Parts Used:
WE03X29897
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
broken belt
Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.
Was this instruction helpful to you?
Thank you for voting!
Customer:
paul from howell, AL
Parts Used:
5303937139
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
thin cloth materials getting stuck between drum edge, leaving rust marks.
lifted up the top after releasing 2 catches with the putty knife, removing front panel, held in place with 2 screws. Scrape off top felt strip with the worn teflon tabs. Wire brush off old glue. Apply glue provided.(thin coating). install new felt strip. let the glue dry for a few minutes, reinstall, and you are done.
Was this instruction helpful to you?
Thank you for voting!
Customer:
giuseppe from sarasota, FL
Parts Used:
WH23X10016
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
Did not drain or spin
Removed old pump and re installed a new one,took no more than 20 minutes,the hardest part was re connecting the trap- hose and the drai n,very easy .Just unscrew the two screws holding the pump and replace it with the new
Was this instruction helpful to you?
Thank you for voting!
Customer:
PAUL from VA BEACH, VA
Parts Used:
5303937139
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Burned Clothes, And Cuts In Allclothes
Popped top off with flat head, took 2 screws out with phillips head, disconnected wiring, took front off, old piece removed, cleaned with razor blade, installed new glide, all done. I am sorry I waited so long to try this. So easy!
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tony from Ukiah, CA
Parts Used:
5303937139
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
clothes getting stuck in drum and leaving brown marks on them
I want to suggest that you also purchase the lower drum seal or guide as well. When I took it apart I realized I needed it also.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Herbert from Randolph, ME
Parts Used:
131862900
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench set
bad rumble when running
released hold down clips on top and removed two screws at the bottom of the front panel and firmly pushed down on the panel to release it exposing the motor drive assembly and idler tension pulley i released tension on the drive belt removed the pulley from the assembly replaced it with the new pulley including the pressure washer which keeps the pulley stable realigned the belt and replaced the front cover and closed the top. done.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from Flagler Beach, FL
Parts Used:
5303937139
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Squealing after dryer running 20 m inutes
Installed Upper Drum Glide. Fixed problem 90%. Sprayed silicone on pads and squeal almost all gone.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Albert J. from Homosassa, FL
Parts Used:
134101800
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
I had no problem
I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Cecil from Jacksonville, FL
Parts Used:
131461200
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Washer leaks when spin drying
Put the front up on a 4 X4 block. Removed the two screws at the bottom of the front panel. Slid the front panel down and off. With pliers squeezed the spring clamp and removed the hose, slid the hose out of the machine. Slid in the new hose into the hole in the back, put the spring clamp on the hose, slid the pump end of the hose onto the pump and using pliers put the spring clamp back on. Put the front panel back on and the screws, removed the block. Tested the washer.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeff from Live Oak, FL
Parts Used:
5303937139
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
drum was lose and was marking clothes
watched the video My dryer was a little different but it came apart easily and was an easy fix. My wife did it all by herself.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Pittsboro, NC
Parts Used:
5303937139
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Clothes were getting trapped at edge of drum and were being burned.
Pulled dryer forward for access. Raised top by pressing clips on front. Removed front panel 2 screws. Removed old felt flange with plastic guides. Cleaned surface of old glue. Dried. apply cement per instructions applied new felt. New fit was snug and required some manipulation. When in place it helped to hold felt until cured. works great. Would not have known what problem was without the videos @ Part Select. Thanx for info and part. David
Was this instruction helpful to you?
Thank you for voting!
Customer:
Pete from San Dimas, CA
Parts Used:
WE03X29897
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Sqeaking during operation
I used these two videos to help me clean the inside of the machine, then change the drive belt.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WSM27TCBWWW
121 - 135 of 163