WSM27TCDWWW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- TIM from NORTH AURORA, IL
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bearings,belt squeaking
Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Orange beach, AL
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter was bent and screen torn.
Ordered a new lint filter around 2 pm and received it UPS the following day. Popped it in and we're good to go. Could not have been faster or easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Silver Spring, MD
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
filter was busted
Replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from hudson, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
belt broken
watched video and followed instructions. Made my wife very happy not having to buy a new dryer. Thank You, Joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john l from cumberland, RI
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Belt Was Broken
I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pauline from Kelseyville, CA
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wouldn't rinse, spin, or pump out the water
Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a full refund was in my bank account. Shop PartSelect with confidence. I will be back!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald C. from Smithtown, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Drum wouldn't turn, snapped drive belt
Removing the top and then the front of the dryer went fairly easily after finding the screws. The drum came out with just a little coaxing, does not gets screwed in place. To me the trickiest maneuver was getting my hand under the drum to place the belt over motor pulley and around the tensioner pulley. You must look up an image of the belt routing. It took me forever to figure that out. If not for that, this in a half hr fix. Ps don't forget to unplug the dryer.
Was this instruction helpful to you?
Thank you for voting!