WSM27THAWWW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Lafayette, LA
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washer would not spin
watched the video, all instructions were perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from Warsaw, OH
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The washer lid lock was burned
UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Deshler, NE
- Parts Used:
- 131858004
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tenant lost knob and landlord replaced it.
Just pushed the knob on to the metal on-off control,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Hamilton, OH
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My washer started making a loud, screeching noise and then stopped working.
Following the easy instructions on PartSelect's website, I first removed the screws from the bottom, front of the washer. Then, using the putty knife, I unhooked the clips holding the washer top to the front and pulled off the front. I pushed in the belt wheel and removed the old belt, which was being held on by one strand. Then, I put on the new belt, put the front back on, replaced the screws and then pushed the washer lid back down over the clips. It worked perfectly and took less than 15 minutes and cost me next to nothing. Thanks for a great site!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rickey from nashville, TN
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bad drive belt
remove old belt, install new belt
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pauline from Kelseyville, CA
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wouldn't rinse, spin, or pump out the water
Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a full refund was in my bank account. Shop PartSelect with confidence. I will be back!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Port Monmouth, NJ
- Parts Used:
- 134511600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Belt stretched out
lifted up top panel unscrewed two phillips screws at bottom of front panel, lifted up and out and removed the panel exposing motor and belt .pushed in belt tensioner and removed belt.Then I slid the new belt under the tub pulley and rotated it until belt was on both the tub pulley and motor pulley,released belt tensioner and the job was over,
Was this instruction helpful to you?
Thank you for voting!