GWL2060RBL General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Leigh J. from Aurora, IL
- Parts Used:
- WH41X324
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Water Leak
There was a hose clamp that needed to come off and put back on the new hose, and POOF....back in business again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Delray Beach, FL
- Parts Used:
- WH13X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hot water would not pour out at normal rate.
This was a very easy repair. First I unpluged the 120VAC power cord. Then I turned the water off. Next I opened the hose connections. Then I removed 3 screws from the back which exposed the Inlet Valve. I removed the old valve taking note of where the wires went. Then I installed the new one. It took less than 10 minutes!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from millen, GA
- Parts Used:
- WH1X2757
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
teeth worn off of knob
removed old knob pushed on new nrw one locked on wifh key
Was this instruction helpful to you?
Thank you for voting!
Water leaking out the bottom of washer during fill
Removed back cover. Opened top lid - slid putty knife under front lip to release latch (2). Removed old valve hose and clamps. Replaced with new valve hose and new clamps. No more leaking during fill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leigh J. from Aurora, IL
- Parts Used:
- WH13X81
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Water leak
I took the back cover off of the washer, studied my next move and jumped in.Easy Lou-eezee!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodney J from Derby, KS
- Parts Used:
- WH13X81
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No hot water entering machine.
Did some checking to make sure the filter, screen and hose were unobstructed. Turned off water at faucets, disconnected hoses and drainage hose. Unplugged machine and pulled out far enough to access back. Used nutdriver to remove 6-7 screws that held the back on, and then inlet valve plate. Removed clamp on outlet hose, then one by one removed wires, making sure to connect them to the same connections on new valve. Re-connected outlet hose and reversed procedure. Easy fix. Went ahead and replaced hoses while I had it out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Dana Point, CA
- Parts Used:
- WH13X81
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
no hot water
Pulled top off and removed corner mounting plate then unscrewed mixing valve.replace wiring to valve and mount new valve in it's place .put back support and corn brace .then attached hoses and put back in service .work great for 20 plus yr machine.thanks tom
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Summerville, SC
- Parts Used:
- WH13X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
No water going into the washer at rinse cycle
Took off the backing and then the water inlet piece and just reverse the procedure when installing the new part. What really amazed me was the ease of ordering the part through this website. I found it, ordered it and in two days it was here!! Great website, you folks really know what your doing. My repair was under 25 dollars, how much would have I paid for a service tech to come out, don't even want to think about it !! I'm telling everyone I know about your website. THANKS AGAIN !!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zhiyong from North Potomac, MD
- Parts Used:
- WH1X2026
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Washer can drain but not spin, buring smell
Lay the washer on its side, unscrew three screw to loose the rotor, put the belt and screw the rotor back.
Was this instruction helpful to you?
Thank you for voting!
oil leaking from under side
turned washer upside down- had to remove one frame cross member to get to the seal. replaced seal- replaced frame cross member. stopped the oil leak, but had a small rusted hole in the bottom tub. sanded that clean, inserted a rubber snap-in plug that fit the hole, covered with that monkey glue. let that dry for a while then covered that with BJ weld, let that cure 3 days. washer workes fine now no leaks at all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Wilbur, WA
- Parts Used:
- WH8X305
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Water Leaking Onto Floor At The Let Front Corner
Using the 1" putty, push in on the 2 clips holding the top of the washer. Lift top, exposing the top of tub. Remove old rubber seal from top edge of tub. To ease installation of new seal, stretch it over the edge of tub which tensions it, then start tucking the outer lip along the outside edge, tilting the seal towards the outside edge until the seal is completely in its groove all around. I had to hold down on the seal to keep it from rolling off while I lowered the top back down. When the lid is down, push hard to engage the 2 clips that lock it down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Mauston, WI
- Parts Used:
- WH13X81
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Cold water filled very slow
Replaced the water inlet valve. Your shipping was next day the best I have ever received. Thank You
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Mountain View, CA
- Parts Used:
- WH13X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
During non use (overnight) tub filled up with water and overan onto the floor
Turn off cold & hot water inlets. Detached water and drain hoses from Washer. Unplugged electricity.Removed back panel using nut driver/wrench would also work. Detached plate holding old valve and then old valve from plate. Held old valve in one hand, detached each electrical connection from old valve and attched to same location on new valve. Reinstalled and reconnected everything. Work like a charm. $20 bucks instead of a new washer. Point of fact: the valve contains the selinoids that regulate water flow. I did not know this and was trying to find "Selinoid" instead of inlet valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Johnny from New Bern, NC
- Parts Used:
- WH1X2757
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Selector knob would not engage to select wash cycle. Teeth on knob were worn/broken.
Removed existing knob by using pliers to release clip from shaft. Inserted new knob (with clip attached) onto shaft and aligned with shaft groove to engage clip. Easy breezy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from REDWOOD, NY
- Parts Used:
- WH13X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
I closed my vacation cottage for the winter and neglected to put a small amount of RV antifreeze in the washer hoses and the plastic valve developed a hairline crack which sprayed water out when hooked up again in the spring.
Since the valve sprayed water out in one particular spot, it was easy to determine what part I needed. After I received the part from "Part Select" it was super easy to replace and took about 10 min. and the washer was good as new.
Was this instruction helpful to you?
Thank you for voting!