WSM27TCAWW General Electric Washer - Instructions

Removed dryer top. Unscrewed the screw from each side inside the dryer the ones below the control panels. Don't unscrew those you will just have to put them back. Insert a flathead screw driver on the left side to loosen the front panel and slide it gently to the right. You can replace the drum glide without disconnecting any of the wires. Remove old drum glide and clean. Install new one and while the glue dries clean inside the dryer. Mine was very dirty!!!! Put everthing back and your ready to go. Don't forget to hook back the dryer vent. Thank you partselect my dryer is almost like new and is drying so much faster, no more noise and you have saved me lots of money.

removed 2 screws, and released the clips holding the top of dryer. Lift top of dryer to expose drum. Remove old drum guide. Clean old adhesive off. Apply new adhesive, and attach new drum guide.

Works like new now

Took off front door. Cleaned all of remaining felt left.
Put on glue and installed new part.

popped lid pulled front scraped old seal off ,good kit ,worked great. you guys are great 2nd day delivery,on parts for fridge ice maker solenoids and dryer parts. you got me for a customer from now on. thank you. steve

disconneted power removed two screws removed led the front clamp removed quiet hose remplace for new

replaced upper drum gasket(felt) hardest part was removing old gasket(felt) used a wire wheel on a cordless drill and the material came right off job was very easy to complete and got great service from parts select

no problem open top remove front install new belt

tilt up lid, remove front panel, replace guide, clean out dryer and reinstall.

Unhooked old hose and replaced with new one.

Removed the top of the dryer 2 screws. procedure
open dryer door. At the top of the dryer door their is
two screws left to right, Remove them and lift top
off. Inside where the top was is two screws left to
right. Remove the two screws and take the front
panel off. Carefull not to pull wireing loose. Lean door against something so you don't have to disasemble wireing. Pull broken belt out and install new belt around tumbler and up and over
tension pulley and pull down and slip over the motor pulley. Your'e done. Reassemble front then
top. My dryer ran just fine after these steps. The question and answers helped me do this.

This is a space saver one piece unit with dryer on top. I first removed ten screws that hold the top on, I then removed four more screws that hold the front service cover on and two last screws that hold the rear service cover on. Now I seperated the front cover of the dryer from the dryer tumbler tub and slipped the new belt around the tub, then at the rear service cover I feed the belt through the tensioner and back onto the motor pully. Now just put the covers back in reverse order of removal and all done! "Piece of cake"
Ron

First of all to all you females out there, I am one and this is easy. It was a stacked washer/dryer and the dryer is gas. I unplugged the power, didn't unhook the gas and left them stacked, not a problem. Next I pushed in the 2 clips at the top with a small screwdriver while at the same time prying up on the top with my chisel, popped the top up and unplugged the wire bundle that's attached to the front panel. A few inches down on the inside of the front panel are 2 screws, I removed those. Then I pried the front panel off - there are 4 clips 2 on each side holding the front panel on. I pulled off the felt strips leaving a bunch of "hair". I read the other repair stories saying they'd wished that they'd used stronger solvent to remove the old glue and "hair" so I used laquer thinner and it worked great. Just saturate your rag and get the old felt and glue really wet and then come back with the chisel and the felt and most of the glue comes off and not the paint. I just kept going back over it with the saturated rag and chisel and it was pretty easy. I then put the glue on the felt strips, attached them, and used a ring of bungee cords to make a clamp around them 'til they dried. Put dryer back together and it works great. Also when you've got it apart - it's a good time to vacuum out the inside of the dryer.

Removing the top and then the front of the dryer went fairly easily after finding the screws. The drum came out with just a little coaxing, does not gets screwed in place. To me the trickiest maneuver was getting my hand under the drum to place the belt over motor pulley and around the tensioner pulley. You must look up an image of the belt routing. It took me forever to figure that out. If not for that, this in a half hr fix. Ps don't forget to unplug the dryer.

followed on line instructons very easy

This appliance is being used in a third world country with no parts access. I discovered Partselect and easily found the schematic with parts listed. Needed parts were easily identified ordered online and received within 4 days in the US and in time to take on my day later flight outbound. The process was seamless and expeditious. Thank you Partselect!