GUAN275ED0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Oxford, NC
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dryer was squeaking when drying clothes
replaced the parts that had worn out
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeffrey from hertford, NC
- Parts Used:
- WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Loud Squealling noise from dryer
Opened the door and removed 2 screws from inside/top of door. Removed top and then removed 2 screws from back of front panel. Lifted drum slightly to remove front panel and attached new slides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from LIncoln, NE
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Intermittent squeak when first starting the dryer.
Followed the video on this site but did not have to remove wires. Just stand in front and let the front panel rest on your leg while you replace the slides. Quick and Easy!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana M from Middleport, NY
- Parts Used:
- WE03X37317
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Intermittent Squeek Noise
Removed 2 screws from inside door lifted top panel up,removed 1 screw attaching front panel to left side. Pulled front panel out far enough to remove and replace slider bearing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john l from cumberland, RI
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Belt Was Broken
I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from San Dimas, CA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Sqeaking during operation
I used these two videos to help me clean the inside of the machine, then change the drive belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shauna from Bend, OR
- Parts Used:
- WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
High Squeaking noise
I removed the top of the dryer and saw that the top two drum slides where gone and the drum bearing itself was damaged I Temporally placed the parts on the drum bearing until I got the new one, that stopped the squeaking noise. All I needed to do was place the part with the hole on the little hook and then sled the other part in its slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Bristolville, OH
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screeching noise when drum went around
To get to where the drum slides go you have to first remove the dryer top. Then you have to remove the two screws that hold the dryer front/door. Found inside the dryer about an inch down on both sides. Be careful because it will fall off. Lower carefully as there is an electric hook-up on the bottom of the door. On the door top are the brackets that the slides slip into. My dryer has 4 slides. Sold individually for some reason. You are done except for re-assembly. Slip dryer drum back on door, press the front until you hear it click back together. Put screws back in and top back on. You are done and no more screeching!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from hudson, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
belt broken
watched video and followed instructions. Made my wife very happy not having to buy a new dryer. Thank You, Joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Nokomis, FL
- Parts Used:
- WE4M522
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer knob broke.
I only had to replace the "plastic" knob on my dryer. This required no tools- just push on to the stem. This part needs to be improved... should be made out of something other than plastic because this gets a lot of wear. I was very pleased with how fast I was able to order & receive my part shipment. I shopped around for this part & your company beat any other price on the market. THANKS!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angelica from Fayetteville, NC
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Horrible squeaking noise during operation
The only tool used was a phillips head screwdriver. I removed two screws to lift the lid and two more screws to free the front panel, slid off the front panel, and had direct access to all 4 slides, replaced, reassembled, and good as new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- angela from Delaware, NJ
- Parts Used:
- WE03X37317
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
horrible shreaking noise
follow the video, and in no time fix and ran smooth, like brand new, love this website, fast and reliable
Was this instruction helpful to you?
Thank you for voting!