GUSR2080T2WW General Electric Washer - Instructions

First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer

Pretty much the entire machine has to come apart to replace a transmission. The thing to know that no one mentioned is that the hub nut is reverse threaded - that means righty loosey.
Even if I had known, I tried it both ways and I doubt I could have gotten it off without the chisel as the others also had to do. Split ring was also frozen in place by hard water and soap scum so had to break that cheesey piece of aluminum off also. If you are taking apart your washer, I advise ordering these 2 parts so you will have them after you destroy the old ones trying to get to the part you need to fix.

Thanks to parts select for the exploded diagram!

You tube is the only way to go!

Remove agitator. Remove coupling. Reinstall new coupling. Reinstall agitator. My only problem was the 7 day delay in getting the part. I expected 2-day delivery.

Pulled agitator off existing agitator coupling. Removed and replaced agitator coupling. Snapped agitator on. One of the easiest appliance repairs I have ever attempted.

First I disconnect the power and then I pull the front cover and replace the water pump, drain hose, and the inlet hose this was fixed and straight easy job.My second problem was the overfill problem witch I took the knobs cover and I replace the water level switch.This job was also easy but did not fix my problem.

R&R Leaking/Damaged Hose and replaced it with the new one. One thing to be aware of is that after removing screws from the discharge hose upon removing the damaged one there was some water that did not expel from the unit so there was about a cup of water that came out. After removing the leaking hose you will need to remove the retaining plastic piece so that it can be placed on the replacement hose. Or if you ordered one put it on the hose so that it can retain the end of the hose in the washer. The anti-siphon clip is located about half way up the back of the washer it simply clips in place.

This was my daughter's washing machine. I looked at the back of the machine to see if there was an opening to get to the parts. Since the back is all closed up. I knew the front had to come off. I pride up, and I pride out, and finally the front popped off. After taking the front cover off the washer. I could see the belt was all chewed up. We ordered a new belt from partselect and got it a day early. I tried to pry the belt on without loosening up anything. I couldn't get it. So I loosened the four bolts on the motor mount and slid the motor backwards towards the other pulley. I put the belt on both pulleys and pried the motor forward to tightened the belt up. Then tightened all four bolts. Put the front guard back on and tried the washer to see if we had any other problems.

I removed agitator by pulling it up until it unsnaped.

I removed the old agitator coupling by removing the bolt and pulling up while twisting it.

The new coupling looks different than the old part but fits the same.

I pressed the new coupler on to the agitator shaft, reinstalled bolt and pressed agitator on the agitator coupler until it snaped into place.

Washer runs like new!

My son repaired the washer . It was really easy to fix. He had it working in about 15 minutes. Thanks to PartSelect's fast delivery service I was only without my washer 2 days.

Problem was intermittent. It would happen once a month or so. Eventually I set next to the machine and kept turning it On and OFF through cycles for about a half an hour until it failed and I was able to confirm that problem was with the water valve.

Buying and replacing the water valve was easy.

WARNING: UNPLUG THE WASHING MACHINE FROM THE WALL BEFORE ATEMPTING ANY ELECTRICAL WORK ON YOUR WASHING MACHINE!

Our GE washer stopped agitating. We bought us a Whirlpool Cabrio washer with auto-sensing and an impeller instead of an agitator. My wife couldn't get used to washing clothes with so little water. We found out about PartSelect.com and ordered the part they indicated would probably fix our GE washer ($5.86) - the Agitator Coupling Kit. Ordered it on Friday, received it by Fed Ex the following Tuesday. It was an easy installation. Our GE is working fine. Took the Whirlpool back to the store, got our $637.00 back.I plan to use PartSelect.com again,if I need to. We don't like the new type washers as well as our 7-1/2 year old GE.

I watched the video from the web site and the one that came with my invoice. This made it very easy to fix.I got the tools that I needed and went to town on the repair.

First I located the trouble. I noticed that it was water leaking and figured it had to be a hose. I took the front panel off of the washer and after noticing that the drain hose had a slight hole in it, realized that I could fix it and save myself a repair call. I undid the two hose clamps and removed the hose. I went to a local repair shop that could not guarantee the right part. I went online and found Parts Select.com. I entered minimal information and the picture of the item that I was looking for, the Drain Inlet Hose, was staring at me! Within 3 business days and less than 20 dollars spent, I repaired my washing machine. The total time spent to repair after I received the hose took about 10 minutes. I will definitely use parts select .com and recommend to all my friends and family. Thank you.

I had help taking off the old parts,coupling was not easy. But I installed the new parts by my self and I'm 74 years had trouble getting the Agitator Coupling back on, But the straps were easy, Any way I'm back to washing again thanks a bunch