GUAP270EM0WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from LAWRENCEVILLE, GA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The dryer drum wasn't spinning, but I could hear the motor and feel the heat from the heating element.
UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.
The video on the site is easy to understand and a snap to follow.
The video on the site is easy to understand and a snap to follow.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karl from Milford, NE
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Clothes were catching between the drum and front of dryer. Also was squeaking at times.
Opened dryer door and removed two screws that held front of top panel on. Lifted top panel off and removed two screws that held front panel to side panels. Tipped front panel forward and replaced all four slides. Cleaned everything off and put back together. Works great again. Thanks for this site and for others that have done these repairs before and posted their stories.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Kilgore, TX
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
squeeky drum
Pull the two scews to release the top of the cabinet. Pull the two screws to release the face of the cabinet and tilt out.
Take the old slide out and install the new ones.
Put it back together.
No more squeeks
My wife thinks I'm a genius...
Take the old slide out and install the new ones.
Put it back together.
No more squeeks
My wife thinks I'm a genius...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brad from Batavia, IL
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
loud screeching and long dry times
When we first heard the screeching i thought right away that it was the belt. we ordered a new one and after i replaced it the dryer was still just as loud. I wished i went here first. Right away i found others with the same problem, did the same repair which was just taking 2 screws out, sliding the top and front panel off(watch for the electric wire connected to the panel) and replace a couple of plastic slides. now it is better than ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from salem, NH
- Parts Used:
- WE03X29897, WE03X37317
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
slides worn and belt broken
Unplugged power. removed 2 screws to take of top cover. once inside removed 2 more screws to slide front panel of. I first replaced slides on front panel. I then lift drum and installed new belt. Only trick is to make sure you wrap belt around tension arm pully properly. Basically a very easy job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from Round Pond, ME
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My dryer was making a really loud, high pitched squeak and eventually a grinding noise
I order the parts needed to replace the slides, the felt ,and the bearing on a Sunday afternoon. The parts arrived on Tuesday even though I used regular shipping. I followed the instructions posted by another customer. It was extremely easy and only took me about fifteen minutes. My only problem was that I needed 2 each of the front slide and the rear slide, and I unknowingly only ordered 1 of each. I order the other 2 on Tuesday via regular shipping and they arrived on Wed. AMAZING!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- janet from martinsville, IN
- Parts Used:
- WE1X1192
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dryer did not latch
easy to fix took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Hermon, ME
- Parts Used:
- WE3M26, WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squeaky noise
Removed top panel giving access to drum and screws that hold front panel (door). Removed to screws to be able to remove front panel but be careful wires are short not giving you much room to remove panel. Removed plastic Drum Bearing and replaced with New one. Installed slides and put back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynell from PITTSBURGH, PA
- Parts Used:
- WH49X27616
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The rear right rod that stabilizes the tub disconnected from the frame
This was the third time the same rod had disconnected from the frame of the washer. The first time, it took us all day to fix it, trying to hold the tub up and reconnect the rod. The second time it disconnected, it took us all day again. This time fortunately one of the black stabilizer rubber tubing broke off from the tub cover. Thank goodness I found part select, read the reviews on installation and ordered the entire tub cover kit. They had the best price and I received it in 2 days. This time it took an hour to repair!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alvino from newtown, CT
- Parts Used:
- WE03X29897
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Dryer belt was broken
I removed the top cover and the back cover to install new belt.
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Mesquite, TX
- Parts Used:
- WE3M26, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
squealing noise as drum rotates.
Drum was misaligned and scraping againt the appliance housing due to worn-out slides.
Replaced the drum slides 2 - white, 2 - black. Replaced the slide housing (front drum bearing?). This part was worn due to worn-out slides that were missing.
Cleaned out old lint from rear of drum and appliance housing. Put new weather stripping seals on the lint catch exhaust. Checked drum belt for cracks and checking.
Buttoned everything back up and dryer works as good as new. $60.00 for parts, 1 hour labor and the job was done!
Replaced the drum slides 2 - white, 2 - black. Replaced the slide housing (front drum bearing?). This part was worn due to worn-out slides that were missing.
Cleaned out old lint from rear of drum and appliance housing. Put new weather stripping seals on the lint catch exhaust. Checked drum belt for cracks and checking.
Buttoned everything back up and dryer works as good as new. $60.00 for parts, 1 hour labor and the job was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph a from VALLEY STREAM, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
belt broke
had a great video to follow, made it easy to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Kissimmee, FL
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud noise
First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from SOUTHAMPTON, NJ
- Parts Used:
- WE3M26, WE03X37318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
CONTINUOUS SQUEAKING WHEN RUNNING
Open Door /remove 2 screws in top of door opening (this releases the top panel) /Lift top panel off of dryer (it is tucked under control panel) Remove the white plastic "arch" (front drum bearing) on top of door panel / Install new drum bearing and 4 each of the "slides" on the bearing/ There are two on each side of the "front drum bearing"/ Reverse the disassembly process to finish/ . You'll need a standard flat tip screw driver and a Phillips heads crewdriver to do all work
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from SONOMA, CA
- Parts Used:
- WE03X37317, WE03X37318
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
thumping noise with any kind of load
looked at video of dryer disassemble, replaced 4 bearing slides, reassembled. Dryer is perfect now , no noise. thank you for your parts.
Was this instruction helpful to you?
Thank you for voting!