Models > GBSR3140H1WW > Instructions

GBSR3140H1WW General Electric Washer - Instructions

Jump to:

All Instructions for the GBSR3140H1WW
106 - 120 of 644
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
David from Rochester Hills, MI
Parts Used:
WH01X39337
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Wash basin wobbled excessively
Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
jayme from drummonds, TN
Parts Used:
WH23X10030
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set
My washer would not drain the water out.
IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Raymond from TRAVELERS RST, SC
Parts Used:
WH43X10032
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
No Agitation Spins OK
Followed your video instructions and removed agitator.Used 7/16 3/8 in socket wrench to remove bolt in the agitator coupling and replaced coupling. Put new bolt in and tightened. Installed Agitator.Works Great.
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from SELAH, WA
Parts Used:
WH43X10034, WH02X10383, WH02X10265, WH43X10032, WH02X10237, WH41X365, WH2X1199, WH2X1198, WH2X1197, WH01X39337
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Noisy while spinning
I dissasembled the machine and it took about 30 minutes. Orderd the parts recommended for noisy spinning. Reinstalled the new parts / changed all drum straps. Cleaned the drain drum and spin drum and after complete reassembly the washer is still noisy in agitation and spin cycle. The motor,transmission,counter weight,and drum look ok but there is still a reason why the machine is still noisy. Spent 120.00 dollars on parts so far but the drum and motor,transmission and counterweight are very expensive to replace. I am just going to keep using the machine until the washer fails to work anymore. I'm not going to put any more money in the washer. I will just buy a new one. It's not hard to dissasembled and reassemble the washer. I purchased the parts that was recommended to fix the washer but they were not the ones.The new parts did help like the tub seal but the bottom line is that the washer is still noisy. I watched your videos to work on the washer and there were no special instructions on disassembly and reassembly. Like always there must be more than i know to repair this washer. Thanks
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wayne from MINNEAPOLIS, MN
Parts Used:
WX05X20641, WH01X10302
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Washer makes loud whining noise, intermittently, during spin cycle.
The "service kit belt tool" was difficult to install, but I oonsider it a necessity. We tried installing the belt without the tool, and the belt kept snapping off the motor drive pulley. Using a cable tie to hold the belt to the drum pulley did not work. I used a length of heavy duty duct tape instead, and that worked OK. Unfortunately, the whining noise is still present with the new belt, so a GE service technician visit has been scheduled. Our belt replacement effort has not been totally wasted, unless the washer can't be repaired economically, since the old belt was fraying.
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sherri Ann from Rockwall, TX
Parts Used:
WE01X20378
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken Turn On Knob
Just slipped it on. No problems, No Tools.
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
kartik from radnor, PA
Parts Used:
WH41X10096
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Drain hose had a hole in it
used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MIKE from CORAL, MI
Parts Used:
WH12X10065
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
water would not stop at prpoer level
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. put the new part in and that was it.
7 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
patricia from Merced, CA
Parts Used:
WH41X10096, WH16X513
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)
drain hose cracked, leaking water, when in use
It was easy, I just removed the old drain hose clip with a screwdriver. Next, removed the old, cracked hose, inserted the new one, and screwed the new clip in.
The best part about this story is the incredible service I was given, by this company. I bought the machine at Sears, so I assumed I could find the hose their. No, they instructed me to go to Orchard Supply(their sister store), I purchased a drain hose, the clerk told me to buy, but the water was still leaking. So, I went on-line and found the right hose, and now I will continue to purchase what I ned for my machine from your company. REALLY Fast Service. Thanks
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Osvaldo from Madison, AL
Parts Used:
WH11X10049, WH01X10310
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Control knob was striped / cannot rotate dial
Remove control knob and replace it with new part.

One retaining clip to remove and replace part.
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Colora, MD
Parts Used:
WH02X10265, WH2X1193
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Socket set, Wrench set
Very noisy in spin mode
a) remove front panel by depressing the 2 clips at the top in line with the lid b) remove the lid switch and 2 screws holding top on and remove top by tilting up SLIGHTLY and sliding to left. c) Remove agitator and by pulling straight up on it and remove adapter underneath d)remove 4 bolts holding 4 rubber straps to top of tub assembly, readily visible when top is removed. e) unplug motor wiring and disconnect pump and bleach hoses from tub f)while lifting up on tub, push down on each of the 4 suspension rods and disconnect them at bottom of tub ( this is the most difficult part, and to make it easier disconnect the rear rods first) g) tilt tub forward and remove tub assembly h) NOW, for the big nut that holds the spin basket in-- #1, it is LEFT HAND THREAD, so you will turn it to the right to remove it. #2, it is VERY TIGHT and requires a 1&11/16" spanner wrench (which I did not have) for removal. Instead, I used a 1&11/16 socket, an extension and an air impact wrench to remove and replace the nut. Assembly is reverse of removal and remember, that nut is ALUMINUM so be careful with that impact wrench when tightening it back up!I replaced the nut and split ring and cleaned the whole area thoroughly, and it greatly reduced the noise in spin mode. I did not replace the metal housing on the bottom of the spin basket, because it was $50 bucks. this probably would have eliminated all the noise, but my repair only cost $19 in parts, including shipping ,and the parts arrived in 1 day.
6 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roger from Lenoir City, TN
Parts Used:
WH45X10027, WH2X1193
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set, Wrench set
the hub disntegrated . I had to destroy the hub nut to get the old hub off.
I looked at the instructions for removing the tub that are on the back of the circuit diagram included in the panel behind the controls. I followed the directions. As one of your commenters had noted, the aluminum Hub Nut is practically impossible to get a hold on without a special wrench so I chiseled it off. That was the most difficult and time comsuming part . I found some pieces of the old hub in the drain line and blocking the drain pump. Be sure to check for this before reassembling and using the washer.
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Timothy Rathman from CHETEK, WI
Parts Used:
WH41X10096, WH1X2725
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Discharge Hose was eaten through by a rodent
R&R Leaking/Damaged Hose and replaced it with the new one. One thing to be aware of is that after removing screws from the discharge hose upon removing the damaged one there was some water that did not expel from the unit so there was about a cup of water that came out. After removing the leaking hose you will need to remove the retaining plastic piece so that it can be placed on the replacement hose. Or if you ordered one put it on the hose so that it can retain the end of the hose in the washer. The anti-siphon clip is located about half way up the back of the washer it simply clips in place.
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
elie from Santa barbara, CA
Parts Used:
WH41X22935, WH41X374, WH23X10030, WH12X10065
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set
1)pump leak damage,2) water over fill and leak water out the top
First I disconnect the power and then I pull the front cover and replace the water pump, drain hose, and the inlet hose this was fixed and straight easy job.My second problem was the overfill problem witch I took the knobs cover and I replace the water level switch.This job was also easy but did not fix my problem.
14 of 34 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roberto from Nokesville, VA
Parts Used:
WH23X10030
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
some leak
First, remove the old water pump by disconnecting the respective hose, then wipe the area where the pump was, and proceeded to connect the new water pump, of course I did all this with the machine disconnected from the power electric, then proceeded to connect the inlet hoses of hot water and cold water, electricity connected to the machine and did a test with clothes in the washing machine. and now everything is going well, thanks for your valuable help.
sincerely, a satisfied customer
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GBSR3140H1WW
106 - 120 of 644