GCVH6800J4WW General Electric Washer - Instructions

Before disassembling anything be really sure that the little things are reassembled just as they were prior to removal.....

The white door plunger broke after 3 years of use. After replacing the door plunger the door still would not close. so I also ordered the door lock part for inside the washer. This was also an easy replacement but far more expensive. A thing to note. If the door plunger breaks you may need to reset you locking piece. and save your self 130 dollars. To do this. remove the top panel of the washer. remove the control panel. remove the spring ring around the rubber seal. disconnect the door locking piece and remove from washer. now use a hook or stiff wire and loop inside the door plunger hole and pull the lock out. if it wont release ensure the white piece on the bottom is lowered all the way. This is also possible to reset with out removing but you wont be able to check the white piece(the lock holder). What ever you do do not take apart the locking piece it has lots of little parts an will give you nightmares.

Let me begin by saying I'm a woman & don't really think of myself as handy but will try a repair. So at first look we thought we'd have to hire a repairman, but after looking at your website & reading the reviews I realized I could fix it myself (or atleast try). I wouldn't recommend doing this repair yourself without watching the YouTube video showing step by step instructions. It was involved - had to take entire front & top off of washer but overall was an somewhat easy fix. The hardest part to me was getting the 2nd band off of the boot seal primarily due to it's location, so when I put band back on I tried to adjust the angle should I have any other problems. Repair took about 1 1/2 hours but wouldn't have taken as long if I didn't have to fight with nut & bolt on the 2nd band.

This is the second door boot seal that I've replaced on my GE Washer (I don't know the model number). I turned on my IPad, went on YouTube, and found this video: "GE Front Loader Washer Gasket Replacement." I placed the IPad on top of the dryer which was right next to the washer and followed the instructions step by step. I used the pause and play buttons repeatedly to ensure I followed the instructions correctly. The hardest part was placing two retainer rings back on. These retainer rings are used to attach the gasket to the washer drum and to the door opening. When the door is closed it effectively seals the drum preventing water from spilling out or leaking. Before reinstalling both rings, ensure that the gasket is properly seated inside the appropriate grooves on the drum and the door opening respectively. It’s a very tight fit between gasket and metal, so you have to make sure the gasket is properly seated all the way around. The inside retainer ring can be tighten with a Philips screw driver or a small wrench. Not as easy as it sounds because you don't have too much room to work with. I had to grab the drum on the right side and tilt to the left in order to get a little more room for my screwdriver. It may be easier with a small wrench, but I don't have the patience. The second retainer ring goes on the outside of the gasket and the door opening. This ring is spring loaded. Attempt to place as much of the ring inside the groove before the spring loaded tension prevents you from going any further. When you get to this point, take a flat tip screwdriver (careful not to damage the gasket) and hold the retainer ring in place while moving counterclockwise and with a second flat tip screwdriver stretched the ring and popped into place until the whole ring is in place. The guy in the video does this effortlessly with only his hands. The first time I did this, my wife helped me do it. She held the left side while I used two flat tip screwdrivers to stretch the ring, pop in place, hold, stretch, and pop in place until complete. Once you're done you will feel good about yourself and grateful to the gentleman who recorded the video and was nice enough to share. Good luck.

My husband read all of the posted notes and then went to the you tube video noted by one of the postings. He gives excellent instructions and the video can be paused as each step is completed. The most difficult steps were gaining access to the rear clamp and attaching the rear portion of the gasket. Inserted a phillips head driver bit into a 1/2" deep socket and then used the rachet to remove and re-install this clamp.

took off the top and back cover and noticed 4 shocks at the bottom of the Agitator frame. The problem was the Agitator assembly is suspended by 2 big springs and the shocks limit motion, but the whole assembly would move about 7 inches side to side which was not normal, and during the spin cycle it would violently bang the sides and make noise. The shocks/damper had a plastic pin at the bottom, which I pulled out first and the top had to be turned 90 degrees to snap off, so I replaced all 4 shocks with new ones. A bit tight quarters, but I had it done in about an hour. The washer is back to normal now.

Sandblasted spider to thoroughly clean it and increase ductility.We used aluminum foil covered in 5200 on one side to cover holes eaten through spider. Then glued the spider to the drum and filled inside rim of spider with a nice layer of 5200. If the spider was made of stainless steel, the washer would still be running great. Thanks

Accessing the door seal was routine. Removing top and front covers was easy. Lower front cover was a challenge because the leaking door caused the screws holding the panel to rust, so extra effort had to be used not to strip the screw heads. Seal removal was easy, replacing the seal was much more difficult. The majority of the repair time was spent attaching the new seal to the drum. It became a tedious task with a large amount of trial and error. Replacing the front spring clamp also takes some time. Eventually I completed the repair and fixed the problem. I will say that if the washer breaks again, it's going to the dump.

After I disconnected the power and water and turned the washer around. I removed the back panel cover and the top and back panel to get to the pulley wheel. Once I remove the retaining nut and pulley the wheel off the spindle, i compared the new and the old parts and noticed the obvious wear on the old part, luckily the spindle was not damaged and still functional. Placing the new pulley wheel was a little more challenging. Once I seated the pulley wheel with a gentle tap from a rubber mallet. I fitted the lock nut onto the spindle and continued seating the wheel evenly using the nut to the prescribed torque pressure. After I reassembled the washer and reconnected the water and power, tested the washer, and success!

Called a Repair Man, he came installed the part and I now have a working washer once again:)

Remove the bottom panel. Remove the top. Remove the front panel with the door. Romove the two clamps on the boot seal. Remove the old boot seal. Place the new boot seal on the casing around the drum and ensure you put the gasket nozzle and gasket nozzle washer in place. Install the inside gasket clamp with the clamp bolt to the right as you look at it (Note: ensure the nut is over the tab on the boot gasket and stays lined up there as you tighten it. Replace the front panel of the washer and when it is in place put the boot seal on the outside lip (Note: this is the most difficult part as the gaskets does not like to stay in place as you put the outside clamp on. Replace the washer top. Replace the lower panel (Note: while you have the bottom panel off, you may want to clean the debrie trap which is a white pipe and tray that catches stuff that is left in pockets.) For the entire project I used 7mm and 8 mm sockets, flathead screw driver, and a philips head screw drive.

Followed your instruction, very easy. I installed Camco 90" & 45" Brass elbows to relieve strain on hoses.

I watched the video and followed the instructions. First remove power. Remove the rear cover from the control panel and the top cover. Then remove screws that secure the control panel to the frame and remove the control panel. Remove the bottom cover. Then remove the lock ring that holds the rubber boot to the front panel. Remove the door and remove the water inlet pipe. Assemble the machine and run a test cycle.

I saw the video on how to remove the boot seal, and I just follow the instructions. Replacing the water inlet pipe was easy.

Any repair should go easily if you have the right tools and the right PARTS. Like the before mentioned and all went well. The hardest thing about this particular water leak is identifining were the leak is. These parts are on the top of the washer. Take the top off and whamo there it is the cracked fill tube and smashed to hell washer. Real easy to replace. BUT that is really putting a band-aid on the problem. To me this washer was poorly designed by GE. Washer sits on a thick rubber mat, which sits on a conrcete floor and still jumps around, mainly when towels are in it.Fix that problem and then replacing these parts is a one time deal.