Models > GBSR1080A2WW > Instructions

GBSR1080A2WW General Electric Washer - Instructions

Jump to:

All Instructions for the GBSR1080A2WW
91 - 105 of 1054
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Joe from Gig Harbor, WA
Parts Used:
WB23M24
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
one burner would not work
I turned off the breaker to the range. I removed 5 screws holding the control knob carriage. I loosened the 2 screws that hold the control knob to the carriage. I removed each wire 1 at a time from the old control knob and hooked them up to the new one. I replaced all the screws and turned on the breaker.
10 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from Roslyn, PA
Parts Used:
WH01X39337
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
Washer tub was making loud noises.
Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.
10 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Randy from Athens, IL
Parts Used:
WH12X1000
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
The plastic "ears" on the timer assembly had broken off. So when you tried to turn the knob, it would just spin without contacting the gears.
I first removed the screws from the top of the washer electric panel. Then pulled it forward. I then removed the plastic clip from behind the knob. Then I removed the screw holding the timer in place. And then removed the one single wire and the connecting plug. I then plug both wire assemblies in to the new one, slid both ears under the brackets and inserted the one screw. Then just put the screws back in the top. It works great!!!!!
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Old Lyme, CT
Parts Used:
WH23X10030
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Pump went bad, machine had very little use would not buy another GE washer
Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gigi from Monroeville, PA
Parts Used:
WH43X139
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
There was no fabric softener dispenser
The cap just removed by tapping a few times with a screw driver and hammer. then pulling upward it came off and I placed the new dispenser on. a couple minutes saved me from running up and down to add softener and it was very inexpensive.Thanks alot PARTS SELECT.
10 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from New Albany, IN
Parts Used:
WH1X2754
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Timer knob had broken
First off, the repair part arrived in only two days. The schematic was very detailed and accurate on your web site. Once the part arrived and removed from the bag, it was a snap to install with just a needle nosed pliers. Total time was less than 5 minutes. This was the first time I had used PartSelect and you can bet I'll be back. Thanks again. Gary K. in IN.
10 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mary from Timberon, NM
Parts Used:
WH1X2026
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
broken belt
It was very easy, just one screw to get the belt on, then it was just putting in place and putting it back together took the longest.
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leonel from Biddeford, ME
Parts Used:
WB21X5301
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Oven would not maintain set temperature
No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140
11 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Lapeer, MI
Parts Used:
WH45X10027
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The zinc drive hub that connects the transmission to the tub had corroded away.
It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.
10 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rick from Ephrata, PA
Parts Used:
WH1X2026
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Washer would not spin
Removed the front panel with a stiff putty knife, removed the worn belt. Placed the new belt on the front pully and than the rear pully, turning clockwise. After checking the spin cycle I put the front panel back on and I was done.
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Philip from Sugarloaf Key, FL
Parts Used:
WH13X10024
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
washer over flowed due to stuch valve
turned off the water and removed the hoses. Then removed the screws that held the back plate (that contains the knobs). removed the two screws holding the water valves and the hose to the washer. replaced the valve and then reassembled the rest.
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve from Surprise, AZ
Parts Used:
WB44K5012
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set
The Bake Element Split
This was so easy I should be a repairman! Turned off power at the breaker, used socket to unscrew two hex head screws, pulled out element slowly from the back of oven wall - enough to expose the wires about 3". Used pliers to remove clips from terminals, put new element in, pushed on new terminal clips, fed wires and terminals back through the two holes, replaced the hex head screws, turned breaker on and wallah! My wife was happy! That's a good thing.
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from Douglaston, NY
Parts Used:
WH45X10027, WH2X1193
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
Agitator would not spin due to disintegrated hub.
I pulled agitator off revealing rotted hub. Had to remove inner basin from machine. This required pulling off top and tying up to be out off way . I had to get the control panel out of way. Removed back screws and moved it up as though hinged. I had to remove the water fill piece, as this was impeding removal of basin. I had to remove top ring off of inner drum. Needed a second person to hold control panel away as I removed drum. Once drum was out, it was an easy task to replace the rotted hub. I then needed to get the portion that was rotted and still on drive out. Could not wrench the hub nut out due to lack of leverage. Split nut with a chisel. Once old nut out, I cleaned up threads, put inner basin back in, again utilizing assistance in holding control panel out of way. Reinstalled in order. Before I had gone too far, I found that a six pronged jumper had fallen off of the controls. Found where it had been and re-installed. Put remainder back in reverse order. Machine back on line, and working properly.
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gene from Eddyville, KY
Parts Used:
WH38X10002
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Socket set, Wrench set
transmission not working
Should be noted that the basket must be rotated on installation to find the best balance point!
12 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles Wayne from Forest Hill, WV
Parts Used:
WH41X10096
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Hose would not seal at rear of washer.
The hose has a tapered end that fits in a tapered hole in the back of the washing machine.When insalled the first time,the joint leaked badly.My solution was to coat the hose end and the interior of the hole in the back of the washing machine with silicon sealant;let it set up for a few minutes and install the new hose.This solved the leak and the hose seems to be working fine now.
8 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GBSR1080A2WW
91 - 105 of 1054