56421DAWW General Electric Washer - Instructions

Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry to wash :-)

After reading all the repair info and reviewing the diagram for my wash machine on this website I was ready to tear into my washer. I removed the front panel and lid to access the tub, pulled out the plastic agitator and revealed the broken inner base hub. The base hub was cracked half way around causing the inner tub to drop down and drag on the outer tub, making the washer sound like it was coming through the wall on a spin cycle. I then unbolted the plastic cap and removed it revealing the hub nut. The most valuable piece of advice in the repair info was abouthe hub nut being a laft hand thread (clockwise to loosen)and that it was on really tight and hard to remove. I put a short 8" pipe wrench on it, because of the lack of clearance in the tub, and hit it with the handle of a all steel hammer to break it loose. Unbolted the balancing straps (4) on the plastic top rim cap that holds the tub in place, unsnapped and removed it, then carefully pulled out the tub. I also had to unscrew the the control panel to reveal and remove the 4 screws holding the fill tube brace so I could push it back to remove the tub. I then took the inner tub outside and took it apart, 3 parts. The top plastic rim, the tub, and the broken base hub that are held together with torx screws. Then it was cleanup time, very dirty on the inside, used a garden hose, scrub brush, sponge, and soap. Cleaned up the hub nut threads with a wire brush and then the outer tub withe a sponge and shop vac. When the base hub broke it caused the inner tub and outer tub to rub together making a groove and plastic shards on the bottom of the outer tub that I had to scrape and sand smooth. A shop vac an absolute necessity in getting all the grime and plastic crumbs out of the outer tub so they don't get in and clog the pump. I received the replacement parts in 2 days! Reassembled in reverse order and everything worked great! Not a bad project at all when you know what to expect, thanks to Part Select.com.

Top panel was exactly what I needed and fit perfectly. To replace the top panel I first unplugged power. Removed control panel on top of machine. Removed front panel by placing a putty knife under front corners and pushing down on front panel. Removed two screws holding top panel to frame. Removed lid switch from top panel then removed lid from top panel. Lift up front of top panel and slide out of cabinet. Replaced new top panel in reverse order. The only thing I overlooked when ordering top panel was the plastic bumpers and rubber guides for the lid. Had to remove old parts from old top panel and use them. Overall job took about 45 minutes.

Placed a small rope under the agitator and pulled up with a sudden jerk . It popped right up and out . I removed the bolt holding the coupling .I then removed old coupling and replaced with new coupling and bolt. I then installed new agitator pushing down until it clicked into place . All done , less than 15 minutes . Thanks to others that gave their feedback so we could learn what to do .

First and foremost, the job would have taken 2 hrs instead of 8 hrs. The problem was that no one on the help instructions said that the Hub Nut had a LEFT HAND thread and suggested to just break the nut off. Well, after chiseling off most of the nut I drilled small holes through the nut and removed the nut pieces. However; I learned that I had damaged the transmission seal and had to buy a new transmission $183. Had I known this the job would have taken much less time and at a cost of about $50.
PS: The washer runs great.

Fold back control panel, pull water level knob off, and unlatch pressure switch. reverse procedure to install new switch.

Repair went good, only wish i had bought a new tub seal, washer, an split ring....but i managed to save the original ones an it seems to be working like new again! thanks Partselect!!!!

Took about 10 Minutes to have my washer up and running again. So easy, and I almost bought a new washer! Fixed it before my husband got home from work. Thank you PartSelect!

Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.

I had no difficulty dismantling the washer until I got to the hub nut. It was frozen to the cone shaped fitting it was resting in. I had to take a drill and a 3/16" drill bit and drill the flange of the hub nut and then take a chisel and break it off piece by piece. Once that was off, I lifted the tub out and tried to pry off the split ring under the tub and it too was corroded and broke when I tried to pull it off. So I would advise you to buy a hub nut and a split ring if you are replacing the tub bearing, just to be safe. I went to an appliance parts store here in town and bought them. When reassembling the tub, I couldn't get a wrench or pliers on the hub nut to get enough torque to tighten it securely. And since I didn't want to spend $43 to buy a spanner wrench for a one time repair, I went to Harbor Freight and bought a $15 dollar adjustable wrench and cut 3 1/2" off the handle so it would lay flat to the tub and used a hammer to tap on the handle to tighten it securely. If you do not find some way to tighten the tub securely, it will come loose in the spin cycle like it did on me twice before I purchased the adjustable wrench and modified it to work. Plus I still have a useable adjustable wrench. Additionally, I took the washer cabinet, the tub and the tub sleeve and power washed it to get years of grime off of it. The washer now operates like new, saving me hundreds of dollars.

I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.

Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.

First I removed the front panel using the screw driver. I removed the old belt which was in the bottom of the washer. I placed the new belt on the motor and adjusted the pullies. I replaced the front panel. The washer spins much better now than it had for the past year.

The trick is to pull the front cover off by using a putty knife .slide it under the cover at both front corners.it will click on each corner.then pull front cover off .lift off the bottom catch hooks.look for the pump on the bottom right side.unplug the wite connector .take 2-5/16 bolts out holding the bracket.then grab a pliers .squeeze the hose clamps and pull the 2 hoses off.assemble new pump.

Went to PartSelect website, troubleshot the problem I was having for the model washer I have. Ordered part, once it arrived, I had it installed and all back together in less than 30 minutes. Washer has been running with no problems since the repair. PartSelect is awesome!

After unplugging the washer, I drained remaining water from washer tub using my Wet/Dry vac. Ordered new pump Sunday night from PartSelect, 'Standard delivery', part arrived Tuesday morning. Removal & installation took less than 20 minutes.