55198129 General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kristen from ft riley, KS
- Parts Used:
- WH1X2026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
No shake, but plenty of rattle.
We bought this used Hotpoint that was probably one of the original machine created back in the stone-age, it's so old. We've had it 10 months, and it's always had this... burnt rubber stink to it... then one day, it stopped agitating and sounded like a metal bucket of bolts being shaken. We're on a military income with five kids, and the idea of buying a new washer was just... heartbreaking. On a whim, having fixed a washer once before, we opened the front up and painstakingly pulled every last rubber fiber from what used to be the belt. Ordered the part. It shipped quick, arrived quick, and in under a week we were back in business. Someone else had mentioned the needing 1/4" socket, and I was glad I remembered that, because it made is SO much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Kansas City, MO
- Parts Used:
- WH13X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washing machine would not fill
Unplugged washing machine from electrical outlet. Turned off water supply to washing machine. Removed inlet hoses. Removed 2 screws to get panel off that water valve attaches to. Removed the panel for access to water valve. Removed fill hose from water valve and then unbolted valve from panel. Made diagram of electrical wiring to ensure correct placement on new valve. Attached new water valve, electrical wires and fill hose to valve. Installed panel in machine and hooked up inlet hoses. Turned on water supply and inspected for leaks. Turned on washing machine to verify filling and repair was OK.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zhiyong from North Potomac, MD
- Parts Used:
- WH1X2026
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Washer can drain but not spin, buring smell
Lay the washer on its side, unscrew three screw to loose the rotor, put the belt and screw the rotor back.
Was this instruction helpful to you?
Thank you for voting!
oil leaking from under side
turned washer upside down- had to remove one frame cross member to get to the seal. replaced seal- replaced frame cross member. stopped the oil leak, but had a small rusted hole in the bottom tub. sanded that clean, inserted a rubber snap-in plug that fit the hole, covered with that monkey glue. let that dry for a while then covered that with BJ weld, let that cure 3 days. washer workes fine now no leaks at all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Wilbur, WA
- Parts Used:
- WH8X305
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Water Leaking Onto Floor At The Let Front Corner
Using the 1" putty, push in on the 2 clips holding the top of the washer. Lift top, exposing the top of tub. Remove old rubber seal from top edge of tub. To ease installation of new seal, stretch it over the edge of tub which tensions it, then start tucking the outer lip along the outside edge, tilting the seal towards the outside edge until the seal is completely in its groove all around. I had to hold down on the seal to keep it from rolling off while I lowered the top back down. When the lid is down, push hard to engage the 2 clips that lock it down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Mauston, WI
- Parts Used:
- WH13X81
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Cold water filled very slow
Replaced the water inlet valve. Your shipping was next day the best I have ever received. Thank You
Was this instruction helpful to you?
Thank you for voting!