52190117 General Electric Washer - Instructions

Pulled off the handle with the kneedle nose pliers replaced the plastic piece in that, then pulled off the plate that turns the machine on and just snapped the new one on. Only took seconds and saved alot of money. Considering just to have a repair man come to see what was wrong would have cost me $88.00.

I did watch the video, that Parts Select included in an email. After that just follow the instructions in the video. You do need two people to do the job, since the belt needs to be tight. One for holding and one to tight the screws.

Could smell burning rubber as it tried to spin, so figured it was the belt. No, I did no do it the hard way by removing the screws etc. I threaded the belt on the pulleys on one side, and slowly turned them, using my fingers to force thread the belt into place. Worked like a charm.

turn off water outlets, unplugged unit then removed water hoses, then removed the screws from the plate on the washer then removed the valve from the plate then unscrewed the clamp for the water inlet to the washer then removed the hose. then carefully removed the wire clips putting each one on the same connector on the new valve, then put everything back like I did when I took it apart and it works great.

Unfortunately, this washer doesn't have a front panel: to get to the belt, removed the back panel. Unfortunately, you can't get to the belt from there either, unless you turn the washing machine upside down. Since the top of the washer is not level (control panel sticks up), the washer needs to be tipped upside down onto something the washer lid rests on, but keeps the control panel off the ground. We used...a sled. Unfortunately, since it didn't drain the last time used, even though we bailed the tub, there was still a fair amount of water that drained out once upside down. This is a heavy washer - took 3 of us tipping it over carefully onto the sled. We unbolted the motor, put in new belt, but needed to put a piece of the shifter arm assembly in place, which came loose. Took 2 sets of hands to accomplish all this. Works now - 2 small loads of laundry done successfully.

I emptied the washer and unplugged it from the wall. Then i pulled it out so I could get behind it. Next unscrewed the water hoses from the washer. Removed the plate holding the water inlet valve by unscrewing 2 screws holding it to the machine (I used Vise Grip/pliers). Note which side of plate goes up/outward so you can put it back on! Removed 2 more screws that hold the valve to the plate. Remove clamp from valve end to disconnect valve from tubing with a screwdriver. I was able to remove the tubing with a twisting motion even though my washer is way over 10 years old. Remove 4 electrical clips from the valve by pulling them out, (REMEMBER the order of the electrical wires!!). Install new valve by doing this in reverse. Then run test cycle, success and saved hundreds of dollars!

i Had washer up side down took puly out and transmission seal out used screw driver install your part add seal on it tap it back in used socket added quartz of gear oil90 as recommended put every thig back it good experience and saved hundreds of dollars for new ones thank so much for ur video and ur technical people on your site

I followed the instructions on your website to diagnose the problem, select the part needed for the repair, and fix the problem. Everything was as described in the video.

Replaced the water control valve (the thing the washer hoses connect to on the back of the washer) There were 3 bolts that had to be removed and once the part was loose, there were four wires attached, I disconnect each wire from the old part and reconnected to the new part at the same time to keep from getting the wires mixed up. Then I bolted the new part back in place...worked perfect. Total cost of repair was less than 30 bucks...

I looked up the part on line, ordered it and installed. Veru easy since the part that needed repair was right out in the open.

Turns out it wasn't the belt. The belt was fine, worked without water, replaced in washer spot, reconnected water, worked fine. Put clothes in, wouldn't agitate, smelt burning again.

Pulled washer away from wall. Observed problem. Ordered belt. Went on vacation. Cut belt in two to remove. Removed flex coupling to pump. Tried to force new belt onto big sheave, but couldn't really access properly. With help, tipped washer onto its front. Then access permitted forcing new belt onto big sheave by turning (only one direction permitted by gear box). Most of time spent cleaning up oil from gearbox which dripped on floor and splattered on back wall. Wonder how long 15 yr old gearbox will last?

simply replaced the old knob with the new one.

I own a vacation rental two hours from my home. Our guests
said that there was water coming out from under the washer.
I called our local handyman Lolo who is very bright. He came
over and looked at the washer and saw that a plastic part was leaking. He got on your website and put the part number in and we had our part within two or three days of ordering it.
I was impressed by your having this older part-maybe 15 year old washer,the fast delivery since we didn't do it by rush order. I also didn't have to hire an expensive repair service company. We are back in business thanks to your quick service and delivery. We will use you again in the future for sure.
Best Regards,
Trish W Haskell
Borrego Springs, CA

This was a very easy repair. First I unpluged the 120VAC power cord. Then I turned the water off. Next I opened the hose connections. Then I removed 3 screws from the back which exposed the Inlet Valve. I removed the old valve taking note of where the wires went. Then I installed the new one. It took less than 10 minutes!