51270-W0 General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linda from Batesburg, SC
- Parts Used:
- 5303207102
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
strike broken
popped in one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keelyn from Old Greenwich, CT
- Parts Used:
- WE01X10160
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The knob that came with the unit was broken
I took the serial and model # off the appliance, located it on your site, purchased it and it was sent within 2 days. Thanks! I think the old one was a defective one because it never worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Daingerfield, TX
- Parts Used:
- 134211701
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
hose leaking
lifed the lid .remove oud hose and replaced with new hose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from Randolph, ME
- Parts Used:
- 131862900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
bad rumble when running
released hold down clips on top and removed two screws at the bottom of the front panel and firmly pushed down on the panel to release it exposing the motor drive assembly and idler tension pulley i released tension on the drive belt removed the pulley from the assembly replaced it with the new pulley including the pressure washer which keeps the pulley stable realigned the belt and replaced the front cover and closed the top. done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert J. from Homosassa, FL
- Parts Used:
- 134101800
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I had no problem
I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from Warsaw, OH
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The washer lid lock was burned
UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Humberto Aarón from Castroville, TX
- Parts Used:
- 134211701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
The washer hose assembly had mutiple tears in the bellow section of the hose, towards the outlet net the spout.
Used a metal cooking spoon to pry open the lid, held it in place with a chain (mentioned in the tools required) and used needlenose pliers to remove the clamp on the old hose assmbly. Transferd that clamp to the new hose assembly and replace the (1) screw holding it in place. Closed the lid of the washer, and now it is like the problm had never existed. (Very easy fix, 1 of 10 on difficulty scale).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Piscataway, NJ
- Parts Used:
- 131862900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Replace belt
Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off
Was this instruction helpful to you?
Thank you for voting!
Out of country repair needed
This appliance is being used in a third world country with no parts access. I discovered Partselect and easily found the schematic with parts listed. Needed parts were easily identified ordered online and received within 4 days in the US and in time to take on my day later flight outbound. The process was seamless and expeditious. Thank you Partselect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pauline from Kelseyville, CA
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wouldn't rinse, spin, or pump out the water
Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a full refund was in my bank account. Shop PartSelect with confidence. I will be back!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robertt from rio grande, NJ
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
would not drain
followed on line instructons very easy
Was this instruction helpful to you?
Thank you for voting!