Models
>
52050119
52050119 General Electric Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 52050119
Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
$11.00
This plastic clip is a genuine OEM part, used to help connect the timer knob to the shaft on your washer. If the clip has become damaged it will need to be replaced. The clip is found on the backside ...
In Stock
This washing machine water inlet valve has two ports for water to enter.
In Stock
This part is the replacement timer knob for your washer. It is made of white plastic and is about 1 ¼ inches in diameter. The timer knob sits on the timer shaft and allows you to choose the wash cycle...
No Longer Available
This compression ring works in conjunction with the timer dial.
No Longer Available
This coupling is used for 20 spline drive shaft transmissions.
No Longer Available
$15.89
This hose clamp kit contains two clamps. The smaller of the two is an inch in diameter while the larger of the two is two inches in diameter.
In Stock
In Stock
On Order
This seal goes to bottom of the transmission to stop oil from leaking at the bottom of the appliance.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for 52050119
Viewing 5 of 5Leaking
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- jose from lAREDO, TX
- Parts Used:
- WH1X1944
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
Replaced the Agitator coupling
First, you will need to remove the agitator, if it hasn't fallen off by itself. Than, you will need a pulley to remove the coupling from the spinning pole . I used one of those pulleys with three arms to remove it , Second, I lubricated the inside of the new coupling with a little oil, and sided it down on the spinning pole. It was
... Read more
a little hard to installed but, I used a hammer and tapped it in. Third, I also put some lubricant on the new coupling to help the agitator slide down a little easier on the new coupling.
P.S. Check inside agitator for old rubber of the old coupling and remove it. (only if it has fallen off the old coupling.)
P.S. Check inside agitator for old rubber of the old coupling and remove it. (only if it has fallen off the old coupling.)
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- opal from richmond, KS
- Parts Used:
- WH8X281
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench set
lost all gear oil bottom of transmission
put washer on its side,removed 1cross section,loosened the nut that held on the pulley.
loosened the motor and removed drive belt,removed drive pulley,removed old seal,poured in 90 weight gear oil,installed new seal and done everything else in reverse order.
stood washer upright connected water hoeses,waste water discharge hose, ... Read more set washer to spinanr turned it on to make sure no more leaks.
everything is working well
loosened the motor and removed drive belt,removed drive pulley,removed old seal,poured in 90 weight gear oil,installed new seal and done everything else in reverse order.
stood washer upright connected water hoeses,waste water discharge hose, ... Read more set washer to spinanr turned it on to make sure no more leaks.
everything is working well
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Tyler, TX
- Parts Used:
- WH13X81
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Hot Water side barely running
First cut off both incoming water supplys. Next remove the water hoses to the inlet. Then remove some of the screws that are holding the back panel on that will give you access to the inlet plate remove those screws and that are holding the inlet in. when you remove the inlet mark the wires take of the water hose and remove inlet now do t
... Read more
he opposite to assemble There was no Rocket Scientist needed and the funny part $12. cheaper than literally going around the corner to the appliance store Thank You and my wife thanks You
Read less
Was this instruction helpful to you?
Thank you for voting!