MLC275CW6 General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- DAVID from DOVER, NH
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Scraping noise from front of dryer
I had this happen a couple years ago so I knew what to do. The hardest part is getting the old glue off. I did that with some nail polish remover and a paint scraper - probably took 20 minutes just to get the glue off. From there, it's just glue on the new one and slap it back together. In hindsight, however, I would've ordered and installed the lower guide as well and done it all at once.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Alto, MI
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Squeak and clothes getting stuck
Just want to say what a great company to order parts from, I ordered the wrong parts by mistake, broke the part trying to install the incorrect part, emailed customer service and they not only gave me credit for the wrong part I ordered but, also for the shipping...I will definitely be ordering again from this company
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Anderson, SC
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drum noise
Disconnected and moved the unit outside, just to clean the lint out of it. Removed the top, then two screws holding the front panel on. Disconnected the two door switch wires. Peeled off the old upper seal and cleaned surface with wire brush. Applied the supplied glue and clamped the new drum guide in place. While it was setting up, I cleaned out the entire inside of the dryer to eliminate the old trapped lint. Replaced the front panel and mounting screws. Reattached the wires and closed the top. Relocated back inside and plugged it in and reconnected the vent tube. Turned it on and it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Flagler Beach, FL
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squealing after dryer running 20 m inutes
Installed Upper Drum Glide. Fixed problem 90%. Sprayed silicone on pads and squeal almost all gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Piscataway, NJ
- Parts Used:
- 131862900
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Replace belt
Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Live Oak, FL
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
drum was lose and was marking clothes
watched the video My dryer was a little different but it came apart easily and was an easy fix. My wife did it all by herself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Pittsboro, NC
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Clothes were getting trapped at edge of drum and were being burned.
Pulled dryer forward for access. Raised top by pressing clips on front. Removed front panel 2 screws. Removed old felt flange with plastic guides. Cleaned surface of old glue. Dried. apply cement per instructions applied new felt. New fit was snug and required some manipulation. When in place it helped to hold felt until cured. works great. Would not have known what problem was without the videos @ Part Select. Thanx for info and part. David
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from howell, AL
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
thin cloth materials getting stuck between drum edge, leaving rust marks.
lifted up the top after releasing 2 catches with the putty knife, removing front panel, held in place with 2 screws. Scrape off top felt strip with the worn teflon tabs. Wire brush off old glue. Apply glue provided.(thin coating). install new felt strip. let the glue dry for a few minutes, reinstall, and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIM from NORTH AURORA, IL
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bearings,belt squeaking
Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pete from San Dimas, CA
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Sqeaking during operation
I used these two videos to help me clean the inside of the machine, then change the drive belt.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cecil from Jacksonville, FL
- Parts Used:
- 131461200
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Washer leaks when spin drying
Put the front up on a 4 X4 block. Removed the two screws at the bottom of the front panel. Slid the front panel down and off. With pliers squeezed the spring clamp and removed the hose, slid the hose out of the machine. Slid in the new hose into the hole in the back, put the spring clamp on the hose, slid the pump end of the hose onto the pump and using pliers put the spring clamp back on. Put the front panel back on and the screws, removed the block. Tested the washer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert J. from Homosassa, FL
- Parts Used:
- 134101800
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I had no problem
I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from PROVIDENCE, RI
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
drive belt broken....
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vincent from NORTHVALE, NJ
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Drive belt for dryer frayed and making noise
Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- giuseppe from sarasota, FL
- Parts Used:
- WH23X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Did not drain or spin
Removed old pump and re installed a new one,took no more than 20 minutes,the hardest part was re connecting the trap- hose and the drai n,very easy .Just unscrew the two screws holding the pump and replace it with the new
Was this instruction helpful to you?
Thank you for voting!