Models
>
GWX9080R*117
GWX9080R*117 General Electric Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for GWX9080R*117
Viewing 8 of 8
Keep searches simple, eg. "belt" or "pump".
$11.00
This plastic clip is a genuine OEM part, used to help connect the timer knob to the shaft on your washer. If the clip has become damaged it will need to be replaced. The clip is found on the backside ...
In Stock
Order within the next 4 hrs and your part ships today!
In Stock
Order within the next 4 hrs and your part ships today!
This washing machine water inlet valve has two ports for water to enter.
In Stock
Order within the next 4 hrs and your part ships today!
This part is the replacement timer knob for your washer. It is made of white plastic and is about 1 ¼ inches in diameter. The timer knob sits on the timer shaft and allows you to choose the wash cycle...
No Longer Available
This compression ring works in conjunction with the timer dial.
No Longer Available
This washing machine pump is white in color and has four ports for water to pass through.
No Longer Available
$15.89
This hose clamp kit contains two clamps. The smaller of the two is an inch in diameter while the larger of the two is two inches in diameter.
In Stock
Order within the next 4 hrs and your part ships today!
In Stock
Order within the next 4 hrs and your part ships today!
On Order
Special Order
This seal goes to bottom of the transmission to stop oil from leaking at the bottom of the appliance.
No Longer Available
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for GWX9080R*117
Viewing 8 of 8Leaking
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Laurence from Bronx, NY
- Parts Used:
- WH1X2026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
GE washer no spinning during spin cycle
Used the spatula to release the front panel (push flat spatula under top about 2 inches from either side to release the two sprng clips holding the front panel on) to expose the tub and motor assembly. Inspected the belt and it seemed worn and a lot of rubber particles were in base of machine. Ordered the belt from partselect - received i
... Read more
t two days later. Loosened 4 motor mount nuts. Removed old belt and replaced. Tightened belt and tightened nuts on motor. Only tricky part is you will need extensions for socket drive because belt is in the way for two of the motor mount nuts. I used a 1/4" small socket wrench, with an extension. No expertise needed on this one.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachelle from Kent City, MI
- Parts Used:
- WH1X2026
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
washer was not agitating or spinning
My washer was making noise but not agitating or spinning on any of the cycles that I turned the dial to. Didn't know if it was the transmission or something simple. I did some research and discovered it may be the belt, even though the belt looked new, I changed it anyway by just removing the front of the washer and cutting the belt off a
... Read more
nd putting the new belt on by just turning the pulleys until it fed on. No need to tip it over to do the repair...and it WORKED!! Then I did the happy dance around the house...see woman can repair 2!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LLOYD from Moffett Field, CA
- Parts Used:
- WH23X42
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
old water pump was leaking, needed replacment
## WHAT I WISH I'D KNOWN BEFORE I STARTED ##
1. Remove the four hoses first.
2. remove the three screws holding the pump to the structure above BEFORE loosening the flex clamp.
3. with the pump free of the hoses and rest of the washer, then remove the flex coupling clamp from the pump end only; do not remove the flex coupli ... Read more ng from the motor.
4. remove the old pump.
5. attach the new pump to the top of the flex coupling BEFORE attaching the pump to the upper part of the washer. This is the most difficult step, to get the flex coupling on the pump in a secure fashion using the clamp. It's much easier to do if the pump is not yet connected to the rest of the washer.
6. attach the pump to the washer with the three mounting screws.
7. re-attach the hoses.
8. run the washer and check for leaks.
I made the mistake of taking the flex coupling off the motor then tried to put the flex coupling on the motor and the pump when the pump was already attached to the washer. Major grief :>(
Good luck, it's well worth the effort.
1. Remove the four hoses first.
2. remove the three screws holding the pump to the structure above BEFORE loosening the flex clamp.
3. with the pump free of the hoses and rest of the washer, then remove the flex coupling clamp from the pump end only; do not remove the flex coupli ... Read more ng from the motor.
4. remove the old pump.
5. attach the new pump to the top of the flex coupling BEFORE attaching the pump to the upper part of the washer. This is the most difficult step, to get the flex coupling on the pump in a secure fashion using the clamp. It's much easier to do if the pump is not yet connected to the rest of the washer.
6. attach the pump to the washer with the three mounting screws.
7. re-attach the hoses.
8. run the washer and check for leaks.
I made the mistake of taking the flex coupling off the motor then tried to put the flex coupling on the motor and the pump when the pump was already attached to the washer. Major grief :>(
Good luck, it's well worth the effort.
Read less
Was this instruction helpful to you?
Thank you for voting!