GTW460AMJ5WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Heather from CHARLESTON, IL
- Parts Used:
- WH08X37938
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Don’t do this, but we prop the washer lid open so it doesn’t get musty between use; we put a sock or something in there to prevent the striker fro closing. When a family member hops up on the washer to get to the highest shelf in the laundry closet it snaps! And the. The washer won’t function.
REALLY easy-
Just unscrewed the two screws with a Phillips, slid the old one out, the new one set in perfectly, and used the same screws to hold it in place. 2 minute task total.
Just unscrewed the two screws with a Phillips, slid the old one out, the new one set in perfectly, and used the same screws to hold it in place. 2 minute task total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from VERHALEN, TX
- Parts Used:
- WH08X37938, WH08X37938
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lid lock blinks, washer will not operate
Put the parts in, turned washer on.....lid lock still blinks, will not operate. Suggest the control board that sends the signal to the solenoid lid lock switch is defective. Buying a new washer, scrapping this one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from BAREFOOT BAY, FL
- Parts Used:
- WH13X26535
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Water would drip onto the tub when not running
Take cover off use socket driver to remove two hex head machine screws. There was a foam piece attached to the old part that i pealed off and attached to the new part. It’s there to prevent rattles. There is a tube that pulls out of the old part and a grommet inside that must be removed and placed in the new part. Connect the two electrical plugs and install the new part just like the old part came out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kirby from IROQUOIS, SD
- Parts Used:
- WH08X37938
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
The washer would fill with water then stop.
Open up the top of the washer per instructions. Remove the old switch and wiring harness. Install the new wiring harness and switch. The instructions that were provided are very descriptive so the installation went flawlessly. The switch has been redesigned and looks to be more robust than the original. The washer now works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MIKE from POMONA, CA
- Parts Used:
- WH08X37938
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Lid wouldn’t lock keeping machine from working
Unplugged the machine, pulled it away from the wall, didn’t have to disconnect water lines, set the parts out on the counter as I went over the instructions a couple of times, followed the directions, plugged it back in, worked perfectly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricky from KRUM, TX
- Parts Used:
- WH12X27614
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Would not spin
Took 4 screws out of back of control panel. Tested old capacitor. Installed new one. Put back on tested spin cycle everything is doing great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rock from HOUSTON, TX
- Parts Used:
- WH13X26535
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench set
leaking water inlet valve on washer
I watched a youtube video to see how others performed the repair. My washer was a little different than in the videos but the inlet valve was very easy to access once I pulled the washer out of it's "nook". I took off the back panel of the control "box" (4 screws). Then accessed the valve which was held in place with two screws. The screws were buried behind a few wires so they were a little difficult to access but not impossible. I did need to use my 1/4" box end wrench as my son had borrowed my socket set.
The people at PartsSelect were helpful in selecting the right part and the repair is working fine. My wife is happy.
The people at PartsSelect were helpful in selecting the right part and the repair is working fine. My wife is happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Frederick, MD
- Parts Used:
- WH04X29308
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Selector switches were non responsive in operation and diagnostics.
I downloaded the repair manual on line and followed the instructions for running the diagnostics. This showed that the selector switches were faulty. I then replaced the selector switches following the instructions in the repair manual. Couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adelmo from El Prado, NM
- Parts Used:
- WH08X37938
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
the machine was spinning after a load was done,
any electrical device unplug the power cord. I followed the instructions the best I could understand them. but once the part was removed I took pics from my cell phone of how the wiring ran, and also what other connections I had to undo. all connections were made, connected the hot n cold hoses, plugged into the washer no beeps or sounds as before opened the hot n cold water valves, and the tub was being filled with water. could not turn on the washer, no lights or beeps... so I gave up I spent too much time on this machine and money too, hope to get an RMA for the Lid Switch assembly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from STANWOOD, MI
- Parts Used:
- WH13X26535
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Replaced the roller/guides for the upper tray.
Just follow the directions, it's easy. My biggest gripe is with Whirlpool. We moved into this house about a year ago; the dishwasher was new at that time. The house we moved from also had a similar Whirlpool dishwasher, less than a year old. Both had these roller assemblies break. The replacement parts are from Whirlpool, and of much better quality. I don't understand why they don't use the better parts when making the unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from RALEIGH, NC
- Parts Used:
- WH08X37938
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The washing machine appeared stuck in the spin cycle
I watched a video on a few times that PartSelect sent me about how to make the switch from the broken lock set to the new one. And it really went just as the video showed. So far things are working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from GAINESVILLE, FL
- Parts Used:
- WH08X37938
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The machine would not start all the time.
Watched You Tube and had at it. In the end it was fairly simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from GROVE CITY, OH
- Parts Used:
- WH13X26535
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
When not in use, water was dripping into the washer
We are on a fixed income so my wife and I did the repair ourselves. Thanks very much to the instructions George from Clarksville, Tn. provided on your website. She read the instructions and I followed them. the repair went excellent, THANK YOU GEORGE. All is well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry W. from TAMPA, FL
- Parts Used:
- WH08X37938
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Washer would not advance to Wash
Lift the cover, undo too screws, Slide out broken part, slide in new part put in the screws and close the lid.A piece of cake.
Thank you for the super fast service on Christmas eve no less!
Thank you for the super fast service on Christmas eve no less!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from BOSSIER CITY, LA
- Parts Used:
- WH43X24454
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
inner part of fabric softener dispenser base broke off
looked up part not exactly easy. that was the hard part. it was delivered next day and just had to pop into place extremely easy instalation
Was this instruction helpful to you?
Thank you for voting!