GTW330ASK3WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from Oxford, GA
- Parts Used:
- WH23X28418
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Washer would not drain
Unpluged the washer first got as much water out of the drum as possible the leaned the washer over forward and let it rest against something removed hose clamp from pump side and removed the drain hose from pump remove plastic cover and unplug pump push tab and pull remove bolts from pump remove pump install all components in reverse be sure to replace pump to drum seal as well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from BOSSIER CITY, LA
- Parts Used:
- WH43X24454
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
inner part of fabric softener dispenser base broke off
looked up part not exactly easy. that was the hard part. it was delivered next day and just had to pop into place extremely easy instalation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from GALLUP, NM
- Parts Used:
- WH01X24381
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Lid lock bezel broke
Look it up on YouTube to see how to repair the problem. Unscrewed the necessary screws. Took apart the top, pop open the loader replace the bezel. Put everything back together again. Was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from TOLEDO, OH
- Parts Used:
- WH13X26534
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set
Threads on an inlet valve deteriorated; couldn't tighten the hot hose.
Unplug the cord and shut off hot and cold water faucets.
headache avoidance: The male threads of the inlet valve are plastic. Gently turn the female hose ends onto them at the kitchen table with the eventual position in mind then tighten.
1. Remove 4 screws holding shiny metal backplate w/ 1/4" socket (easy)
2. Pry tabs loose, top of plate (easy).
3. Pull electric leads from 2 solenoids (easy).
4. Remove 2 long screws holding upper painted structure (easy).
5. Remove 2 screws holding valve in place (easy).
6. Tilt and slide the valve loose and pull it out (easy).
7. Replace valve and reverse steps 6-1.
n.b. no inside water tubes; water drips straight into tub
Also, an hour should be enough. I spent more time than needed guessing, dealing with a few issues, opening the machine again, starting over, etc.
ps. I guessed at the age.
headache avoidance: The male threads of the inlet valve are plastic. Gently turn the female hose ends onto them at the kitchen table with the eventual position in mind then tighten.
1. Remove 4 screws holding shiny metal backplate w/ 1/4" socket (easy)
2. Pry tabs loose, top of plate (easy).
3. Pull electric leads from 2 solenoids (easy).
4. Remove 2 long screws holding upper painted structure (easy).
5. Remove 2 screws holding valve in place (easy).
6. Tilt and slide the valve loose and pull it out (easy).
7. Replace valve and reverse steps 6-1.
n.b. no inside water tubes; water drips straight into tub
Also, an hour should be enough. I spent more time than needed guessing, dealing with a few issues, opening the machine again, starting over, etc.
ps. I guessed at the age.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry W. from TAMPA, FL
- Parts Used:
- WH08X37938
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Washer would not advance to Wash
Lift the cover, undo too screws, Slide out broken part, slide in new part put in the screws and close the lid.A piece of cake.
Thank you for the super fast service on Christmas eve no less!
Thank you for the super fast service on Christmas eve no less!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from San Luis, AZ
- Parts Used:
- WH16X26909, WH16X26908
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Strong noise when spin, the washer "walk"
>Change 4 rod & spring, (2 red, 2 blue) and
>LEVEL THE WASHER
(this was the initial cause of the failure!)
>clean tub
>LEVEL THE WASHER
(this was the initial cause of the failure!)
>clean tub
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Chickasha, OK
- Parts Used:
- WH23X28418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer wouldn’t drain
Remove old pump install new one. Three bolts and an electrical connection
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHUCK from ZOLFO SPRINGS, FL
- Parts Used:
- WH16X26909, WH16X26908
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer shaking all over the place.
Took top of the washer then took one rod off at a time and replace with the new one, the back two are a little bit harder to do but it works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from LARGO, FL
- Parts Used:
- WH08X37938
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lid was forced open and broke latch
Follow the super simple, precise instructions and it is very easy. Only harder part was unclipping the front of the lid.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Naples, FL
- Parts Used:
- WH44X24385
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced GE Washer lid
Removed parts from old lid (bumpers, switch component and hinges), removed old lid, then replaced parts on new lid. The new lid fit perfectly and looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scotty from OCEAN SPRINGS, MS
- Parts Used:
- WH08X37938
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The machine stopped working completely! My wife went on YouTube,and learned that it could be the motherboard or the door latch. We changed both, and the washer would only fill but did not drain, and spin! We called a serviceman, and he had to program the service board,but said that the new door mech
We changed the circuit board once, and the door latch mechanism twice because we ordered a faulty part. Then we had to hire a service man to program the circuit board, and to inform us that the door latch mechanism was faulty.
Was this instruction helpful to you?
Thank you for voting!