GTW220ACK3WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jason from GALLUP, NM
- Parts Used:
- WH01X24381
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Lid lock bezel broke
Look it up on YouTube to see how to repair the problem. Unscrewed the necessary screws. Took apart the top, pop open the loader replace the bezel. Put everything back together again. Was simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHUCK from ZOLFO SPRINGS, FL
- Parts Used:
- WH16X26909, WH16X26908
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Washer shaking all over the place.
Took top of the washer then took one rod off at a time and replace with the new one, the back two are a little bit harder to do but it works great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from San Luis, AZ
- Parts Used:
- WH16X26909, WH16X26908
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Strong noise when spin, the washer "walk"
>Change 4 rod & spring, (2 red, 2 blue) and
>LEVEL THE WASHER
(this was the initial cause of the failure!)
>clean tub
>LEVEL THE WASHER
(this was the initial cause of the failure!)
>clean tub
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from LARGO, FL
- Parts Used:
- WH08X37938
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lid was forced open and broke latch
Follow the super simple, precise instructions and it is very easy. Only harder part was unclipping the front of the lid.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Chickasha, OK
- Parts Used:
- WH23X28418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer wouldn’t drain
Remove old pump install new one. Three bolts and an electrical connection
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Naples, FL
- Parts Used:
- WH44X24385
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replaced GE Washer lid
Removed parts from old lid (bumpers, switch component and hinges), removed old lid, then replaced parts on new lid. The new lid fit perfectly and looks great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scotty from OCEAN SPRINGS, MS
- Parts Used:
- WH08X37938
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The machine stopped working completely! My wife went on YouTube,and learned that it could be the motherboard or the door latch. We changed both, and the washer would only fill but did not drain, and spin! We called a serviceman, and he had to program the service board,but said that the new door mech
We changed the circuit board once, and the door latch mechanism twice because we ordered a faulty part. Then we had to hire a service man to program the circuit board, and to inform us that the door latch mechanism was faulty.
Was this instruction helpful to you?
Thank you for voting!