GKSR2110B1WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dennis from Middletown, RI
- Parts Used:
- WH2X650, WH01X10310
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Wash Cycle Selection Knob had plastic teeth on the underside that stripped out with years of use.
I used a pair of needle nose pliers and a screw drive to remove the clip holding the knob on its shaft. The new knob came with its clip already in place, so it "popped" right on. I ordered the compression ring in error and it it was not needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristy from Boca Raton, FL
- Parts Used:
- WH23X10030
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
washer failed to drain water from machine
1) Disconnect power
2)remove front panel
3) remove screws and take hoses off
4) remove & replace water pump
:) YAY. all done
2)remove front panel
3) remove screws and take hoses off
4) remove & replace water pump
:) YAY. all done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Covington, PA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
loud noise upon aggitation
replaced Tub dampeners Straps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Marion, MA
- Parts Used:
- WH45X10027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Loud bang during spinning
Remove aggitator, disconect 4 support straps, pry off clips/ latches on top of drum. Remove small bolt that holds on the small plastic unit unto trans.
That will give you access to the large bolt that holds the hub in place. This nut is on tight use a pipe wrench and adjustable wrench and TURN CLOCKWISE TO REMOVE - lock for direction on nut.
Remove the bin gently and turn over to remove the small bolts that hold the hub in place.
Installation is reverse of removal.
That will give you access to the large bolt that holds the hub in place. This nut is on tight use a pipe wrench and adjustable wrench and TURN CLOCKWISE TO REMOVE - lock for direction on nut.
Remove the bin gently and turn over to remove the small bolts that hold the hub in place.
Installation is reverse of removal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leda from Port Saint Lucie, FL
- Parts Used:
- WH45X10027, WH2X1193
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
hub corroded away and left spin basket sitting on bottom of tub.
Biggest problem was getting old hub nut off. I had to remove it in pieces because it was corroded so bad.
Once hub nut was off it was a breeze to replace the parts after cleaning off the threads and shaft.
Reassembled in reverse order.. and ran.
I have to give accolades to PartSelect.. their customer service is second to none. i ordered the parts just before the Christmas holiday and they shipped them to my door in under 24 hours at no extra charge to see that I got them on time...
THANKS!.. It sure helped.
Would I do business here again.. YEP!
I will recommend you to others.
Thanks.
Once hub nut was off it was a breeze to replace the parts after cleaning off the threads and shaft.
Reassembled in reverse order.. and ran.
I have to give accolades to PartSelect.. their customer service is second to none. i ordered the parts just before the Christmas holiday and they shipped them to my door in under 24 hours at no extra charge to see that I got them on time...
THANKS!.. It sure helped.
Would I do business here again.. YEP!
I will recommend you to others.
Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Spring City, PA
- Parts Used:
- WH02X10265, WH2X1199, WH2X1197, WH2X1193, WH1X2026, WH02X10383
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Excessive agitator side movement
Bought all of the parts to remedy this. It ended up being the top transmission seal/bearing which is not a replaceable part. I could see the shaft moving side to side. But the parts diagrams are not detailed enough to show that when assembled.
She led a good life.
My new side loader is SO MUCH BETTER AND INSANELY EFFICIENT. I highly recommend making the change if you need a transmission..
She led a good life.
My new side loader is SO MUCH BETTER AND INSANELY EFFICIENT. I highly recommend making the change if you need a transmission..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Kannapolis, NC
- Parts Used:
- WH45X10027, WH2X1193
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Socket set
Inner tub base hub disintegrated
I had to take the washer outside since there was no room to work on it in the laundry room. The extra space allowed me to spread out the parts, use the garden hose to clean and have light enough to take digital pics of the wiring before I disconnected them to remove the upper panel.
Removing the upper retaining ring for the tub was simple with only 4 screws. The agitator pulled right up and out. The nut cover/agitator anchor removed easily with one bolt.
The tough part was the inner tub base hub nut that I could not get off. Another user had commented on how they had to chisel the nut off and that was the best advice. I used my air chisel on either side of the nut and it was pretty quick to get off - within 3 min. If I hadn't read that I wouldn't have ordered another nut to replace the one I chiseled off.
The diagrams and repair stories really made the difference. Cleaning and reassembling was done within about an hour - cleaning the 11 years of soap scum at least an hour total before and after replacing the parts.
Removing the upper retaining ring for the tub was simple with only 4 screws. The agitator pulled right up and out. The nut cover/agitator anchor removed easily with one bolt.
The tough part was the inner tub base hub nut that I could not get off. Another user had commented on how they had to chisel the nut off and that was the best advice. I used my air chisel on either side of the nut and it was pretty quick to get off - within 3 min. If I hadn't read that I wouldn't have ordered another nut to replace the one I chiseled off.
The diagrams and repair stories really made the difference. Cleaning and reassembling was done within about an hour - cleaning the 11 years of soap scum at least an hour total before and after replacing the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DARYLD from SCHOFIELD, WI
- Parts Used:
- WH41X10096, WH16X513
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hose and clip were broken in moving
The parts were here in 3 days and the repair went very quickly .Quality item would do business again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Hamilton, NY
- Parts Used:
- WH43X10034
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Two paddles on the agitator broke off.
After reading how others have done this and how easy it was, I decided to give it a try. And, sure enough, it was really easy. However, one concern I had was on lifting the old agitator off from the axle using both hands. I didn't want to have the agitator come crashing into my face as I pulled up. So I put a pillow on top of the agitator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lindon, UT
- Parts Used:
- WH01X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broke
Uhhhhhh.... Pulled knob off. Pushed new knob on. Took all of 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Tempe, AZ
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Water was leaking
My husband was unavailable and already overloaded, so I took a screw driver and removed the front cover of the washer. After I discovered where the leak was coming from, I used a screw driver to remove one end of the hose and pliers to remove the other end. I went online, found the part and ordered it. It came in surprisingly fast. My husband put it back in about 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Marietta, GA
- Parts Used:
- WH13X10024, WH41X365, WH12X10076
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
water coming out of bottom of washing machine
was a toss up between the water inlet valve OR the hose pressure switch....why spend more time...I invested in both the water inlet valve and the hose pressure switch and replaced them both....I have the machine torn apart....I spend $45 more dollars...now it's ALL done....and works like a charm...if I were to isolate the problem...I would say, now, the hose pressure switch...but, I am happy and machine probably has 5 plus, more years left...and life is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roman from Amherst, MA
- Parts Used:
- WH1X2026, WH16X544, WH01X10001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Wasing machine strted to make horrible
took it appart and found that the suspension rod was broken. went on line an ordered the parts.
The parts arrived 3 days later. Installed the parts and the washing machine was working within a half hour.
The parts arrived 3 days later. Installed the parts and the washing machine was working within a half hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from erie, PA
- Parts Used:
- WH13X10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
water not shutting off
Removed the screws for the control panel and replaced the load switch and valve body in about 20 minutes. Simple fix and it's working perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darryl from Prescott Valley, AZ
- Parts Used:
- WH41X365, WH12X10076
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water not shutting off when filling tub and over flowing
First figured out tool to use to remove outer covering on control area. Then unplugged units from electric wiring and replugged with new parts.
Parts arrived in a very short time was very pleasantly surprised with the short turn around on ordering and recieving parts.
Parts arrived in a very short time was very pleasantly surprised with the short turn around on ordering and recieving parts.
Was this instruction helpful to you?
Thank you for voting!