GTWP1800H0WS General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from West Columbia, SC
- Parts Used:
- WH41X10077
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Water Leaks
I pulled the top off of the washer and found that my leak was coming from a small hole in the hose and water inlet. I had to remove 2 small bolts and a hose clamp to remove the old part,I did the reverse to install new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tommy from Yelm, WA
- Parts Used:
- WH12X10498
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Could not regulate the amount of water going into the Machine
I shut off the juice to the Washer, I then removed the 4 torx head screws in the panel, so I could gain access to the switch. I then unpluged a small hose going to the switch, then turned the switch by hand about half a turn & it came right out. I then replaced the switch with the new one by turning it half a turn in opposite direction, replaced hose, put the back panel back on, ran the machine to make sure it was working properly.
It is working fine, thanks to Part Select.com , fast service I would reccomend them to my freinds.
It is working fine, thanks to Part Select.com , fast service I would reccomend them to my freinds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia from winter park, FL
- Parts Used:
- WH41X10096, WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
washer leaked water
after reading repair stories, decided I should take front panel off and see where leak was coming from. taking the panel off was real pain but well worth as inside was dry! so I looked again and discovered a pin hole in drain hose that only leaked when tub was full. while I had panel off I noticed tub dampening straps were broken so went ahead and ordered those parts too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LEXINGTON, OH
- Parts Used:
- WH23X10043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Pump died
Followed the video with one exception. The hose clamps were the spring-loaded type and putting the back hose clamp on was a problem, so I substituted a nut driven hose clamp. Other than that, no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joel from mt vernon, IL
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
two tub dampening straps snapped
I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Max from DRUMMONDS, TN
- Parts Used:
- WH12X10527
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Washer would spin before draining
Remove screws from rear top panel. Remove 2 retainer screws for instrument panel. Pull panel forward and then lean forward. Remove electrical connections. Remove screw that retains module. Pull know for selector outward . Push retainer clip out using screwdriver. Remove know. Tap shaft to pop module out . Replace module and installation is reverse of removal
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helmut J from New Berlin, WI
- Parts Used:
- WH12X10276
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water, spin cycle not functioning
After receiving the wrong part 2x instead of magnet assy I received a metal clip ring. ordererd magnet assy from another source. iNSTALLATION IS VERY SIMPLE. REMOVE 2 SCEWS IN THE LID WHICH HOLD THE MAGNET IN PLACE AND REPLACE THE MAGNET WITH NEW ONE. TEST TO MAKE SURE ALL OPERATIONS ARE NORMAL.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from OVERLAND PARK, KS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Water temp will fill hot only with lid open. Close the lid and it is cold water only.
The video I watched said to remove front panel, control panel, and top panel. After I removed the front panel, I was able to remove the lid switch and splice the wires together and reinsert in the mounting without removing the other panels. Secured with wire tie and put front panel back in place. This did not, however fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dennis from harwinton, CT
- Parts Used:
- WH41X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Leaking at housing
This was not hard to do.removed top screws and back plate screws. Water inlet valve has 3 screws and a hose clamp.this job was thirty min. tops.goes back together much faster then taking it apart.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gustavo from Harlingen, TX
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Shaking and making loud noise
removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Rosemead, CA
- Parts Used:
- WH23X10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
wasn't draining the complete water
really easy repair, just open the front cover panel & removed the Drain Pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tiberiu from CLEVELAND, OH
- Parts Used:
- WH43X10034
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
AGITATOR BROKE
pulled up on agitator and it came off and replaced it with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Belinda from FLORENCE, KY
- Parts Used:
- WH41X10096
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
cracked drain pipe
Remove two bracket screws. Removed hose. Put new hose in place using same bracket and screws. inserted end of hose into washer drain. Secured hose to cold water hose with two zip ties.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from DAGSBORO, DE
- Parts Used:
- WH43X139
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
the washer had no fabric softener dispenser
I went on this web site and watch the video to install the dispenser and it was as easy as shown. it only took me less than one minute. I am very happy with my new dispenser.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annamarie from FORT LORAMIE, OH
- Parts Used:
- WH43X10032
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator did not agitate
Removed agitator with rope idea. One quick jerk and it came off. Removed coupling. Replaced with new coupling. Reinstalled agitator. Works fine. Note: I could not see anything wrong with the old coupling. It looked brand new with no noticeable wear!! Thanks for your help in recommending the part that most likely would fix the problem.Tom
Was this instruction helpful to you?
Thank you for voting!