This replacement lid lock keeps your washing machine door securely closed during the wash cycle. If the washer won’t run or the lid won’t stay locked, this part may need replacing. Installation is sim...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This agitator assembly is designed for use in top-load washing machines, where it plays a crucial role in the cleaning process by rotating back and forth to help lift and move clothing through water a...
If your washer isn’t spinning or agitating like it should, this shift actuator might be the fix you need. It helps your machine switch between wash and spin cycles, and is usually found underneath the...
This drive belt is an authentic OEM replacement part for your washer. Over time the belt can become brittle and snap or become stretched out. If this happens the washer drum will not spin, may be nois...
If your washer isn’t filling up like it should, this water inlet valve might be the fix. It controls how warm and cold water enter the machine during a cycle. When it stops working, your washer might ...
This right-side suspension rod and spring assembly helps stabilize the wash tub and reduce vibration during operation. It’s a genuine replacement for select GE washing machines and is designed for dur...
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tamara
February 6, 2022
Fills up & agitates but will not go on to the rinse and spin cycle. I've replaced the lid lock & the striker.
For model number GTW330ASK0WW
Hello Tamara, Thank you for the question. We suggest testing the Speed Sensor. If you are using a multi-meter to test the resistance, the readings should be around 1 or OL is it isn't defective. If it is closer to 0, then it is a short circuit and is defective. We hope this helps!
Replaced belt and speed sensor. Now, when plugged in, it acts like it’s not getting power at all. No lights and no sounds. Checked the outlet, breaker, and power cord; all are working and have power. Next guess is control board or wiring harness? Is there something i’m missing?
For model number GTW330ASK0WW
Hello John, Thank you for your inquiry. It could be either the harness or the control board, but we would also recommend checking the lid lock assembly as well, which you can do with a multimeter. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
I thought it was the control board from the onset, but 'Online experts" said it was more likely the mode shifter or the lid lock. I ordered one of each, did not correct problem. Ordered the control board that was designated for this unit, it did not correct problem. Defective? Was send replacememnt, did not fix problem. Twice? Phone conve
... Read morersation with parts person, and after a little digging, it was NOT the correct board, correct board was not available. Returned all parts, refunds all around. Ordered correct board from another site, installed, programed, SUCCESS! Total repair time/installation-less than 15 minutes. Getting the correct part 30 days.
