This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
In Stock
Order within the next 6 hrs and your part ships today!
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
In Stock
Order within the next 6 hrs and your part ships today!
This genuine OEM part is a lid lock striker for your washing machine. It is located on the lid of your washer and is used to activate the lid switch. The strike pushes against the lid switch to indica...
This drive belt is an authentic OEM replacement part for your washer. Over time the belt can become brittle and snap or become stretched out. If this happens the washer drum will not spin, may be nois...
In Stock
Order within the next 6 hrs and your part ships today!
Order within the next 6 hrs and your part ships today!
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Peter
June 3, 2022
I bought this washer used for free and was told it was about 6 years old. The washer was not working and when i ran the error code diagnostic, i got five codes! One of the error codes was "mode shifter failure" and the other 4 were all "lid lock/switch failure". I bought and installed a new lid lock sensor and i am still getting all the same error codes. The washer's behavior is that when you close the lid and press "start" it jerks to life, gives two spurts of water and then pauses and the fill light comes on and then nothing....
i unplugged the washer in the hopes of resetting the error codes, but that didn't seem to do anything.
For model number GTW330ASK1WW
Hello Peter, Thank you for your inquiry. When you mentioned you replaced the lid switch/lock assembly, did you also replace the lid lock harness as well, part# FIX11759139. Researching the model number that you have provided, the mode shifter is part# FIX16554752. If it is not filling with water, it could be an issue with the water inlet valve, which you could test with a multimeter. The other two things it could be are a faulty control board or the wiring harness. Check the board and harness for any visible damage or loose connections. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.