GTW750CSL0WS General Electric Washer - Instructions

I unplugged the machine from the power source and removed the drain hose from the back and allowed any remaining water to drain out of the machine. I then tipped the machine back so that I could work underneath it and secured it in that position. I removed the old drain pump assembly by first disconnecting it from the outflow hose, then removing the three bolts which held the motor housing cover on and disconnecting it from the power source. This part was the the most difficult and time-consuming as the wires are plugged in very tightly but once those were separated, it was just a matter of unscrewing the drain pump assembly from where it was anchored to the underside of the washing machine. I simply reversed those steps to install the new one and it was in place within 10 minutes. Set the washing machine down in the correct position, reconnected the drain hose, and plug the machine in. I did reset the fault codes by using the manual found taped to the underside of the machine, but this was very simple to do and only took a few minutes. I’m not sure if it was necessary to do that step at the machine works perfectly now. I am a woman and found this repair very easy to do.

Dipped water out as much as possible,tited washer at a 45 degree angle and propped it up. Took the 3 bolts out holding the pump assembly and the 3 bolts holding the belt guard.Unplug wire connecter,pull out assembly and than pull drain hose off of assembly. Reinstall the same as you take apart. Was a easy fix, and worked as it should.

Removed the center agitator to clean it - had black mold and pink soap scum buildup underneath that you couldn't see or clean without taking it apart. Removed the bolt with ease. Upon tightening the bolt back in place, the bolt sheared in half, leaving the lower half threaded in place and the head in the socket. Had to use a drill bit and drill out the lower half of the bolt completely. Ordered the replacement bolt and reassembled everything in less than 5 minutes. Replacement part was perfect - hopefully it lasts longer than the original bolt.

We disconnected the rear of the dashboard and folded it toward. We unsnapped the top cover and exposed the lid lock. We removed the old lid lock and replaced it with the new parts from SelectPart. Put it all back together.

unplugged old part plugged in new, took about 2 minutes.

this is a great web site, I didn't have to wait for a serviceman to come. and maybe not have the part and come back again. ........thanks

I contacted parts select and entered washer information and asked them if they thought they would now what the problem was and and they responded with a answer and also a list of two parts that they thought might take care of the problem. I ordered the parts,looked on u tube to see how to change them and replaced both parts .I think the clutch was good but the drive belt was stretched and needed replaced.Know it works great.

Unplug washer; turn off hot/cold water valves at wall. Access rear of washer; remove 2 long screws anchoring control panel; remove 3 short screws along top of control panel; remove panel; rotate panel forward to rest on washer top (disconnect orange pressure attached to green computer panel. Blue water valve assembly is obvious! Remove hot & cold inlet hoses from washer (have bucket handy to catch water in hoses). Take picture of old water valve so you can reinstall electrical clips in exact same sequence! Remove 3 short screws that anchor water valve; lift out water valve; disconnect clips; gently life out old water valve. Install new water valve in reverse order.

Use needle-nose pliers as a lever to remove tight electrical clips (they are not designed to come loose easily). Google online videos. Really easy, when you watch a couple videos!

I just took old one out an put new one in

The drain pump had three screws. Frist unplug the machine and turn the water off. And unplug the hose for the Hot and Clod Water. Make sure their no water in the tub. Unplug the pipe from the Tub. The unscrew the nut for the connector. Then unplug the connector and be careful not to damage plug for the connector. Press the plug connector with your finger or long nose pliers . Then just hook the new plumb and you all set.

Put the parts in, turned washer on.....lid lock still blinks, will not operate. Suggest the control board that sends the signal to the solenoid lid lock switch is defective. Buying a new washer, scrapping this one.

REALLY easy-
Just unscrewed the two screws with a Phillips, slid the old one out, the new one set in perfectly, and used the same screws to hold it in place. 2 minute task total.

Replaced water pump. Washer now works as new.
Wife is now happy!

Took the belt cover and then replaced the pump. Did a dry run and everything was fine.

The parts I ordered were made of junk plastic and did not match up with the the existing parts. The parts did not end up fixing the problem and I bought a new washer instead.

Waste of money

1 Disconnect power 2) Cut water supply to washer 3) Disconnect water supply hoses from supply.
***if pump broke with water in tub, remove water from tub. 4) tip machine onto it's front side 5) remove hose clamp of exhaust hose & then remove exhaust hose from pump 6) Remove pump with socket/ratchet 7) disconnect pump electrical plug 8) tell old pump to take a hike & throw in garbage 9)Iinstall new pump 10) Do steps 7—1 in reverse order to put back into business.******Be prepared to do it again in 6 months; I havnt had good luck!