GCWN4950D2WS General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Timmy from Fairport, NY
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Banging noise when it was agitating
removed front washer cover (2) clips at top released with straight screwdriver . removed washer top cover (2) 1/4" head screws that are behind front washer cover. Then removed screws holding tub dampening straps (4)5/16" head from agitation drum housing from top, removed other end of strap from under side (4) 1/4" head screws. then assembled with new straps in reverse order. easy repair nice and quiet again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from LEXINGTON, OH
- Parts Used:
- WH23X10043
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Pump died
Followed the video with one exception. The hose clamps were the spring-loaded type and putting the back hose clamp on was a problem, so I substituted a nut driven hose clamp. Other than that, no problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arlis from Moore, SC
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Tube Shaking Like Out Of Balance. Water Not Draining Completely And Created An Unpleasant Odor
Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrance from Eldom, MO
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
A banging noise while the machine was washing.
The repair was done like the video suggested to do and in the order. And it worked well.In the step by step procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from Beverly, MA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
broken dampening strap
Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.
Replaced four broken dampening straps, washer is quiet and all is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from Bynum, TX
- Parts Used:
- WH41X22935
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
had a pin hole in the drain pipe
order the part and replaced it and it works just great! May I add never before have I had such an amazing experience in dealing with your company, your company shows pictures and I ordered the part in the late afternoon and I had it the next day, the diagram you show on your site was so helpful, you told us that the part now is replaced with a different #. Once again KUDOS!! to your co.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from Steamboat Springs, CO
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broken tub strap
follow youtube vid. simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Casper, WY
- Parts Used:
- WH2X1197, WH02X10383
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
it was leaking
my son repaired it. I was told that I had to by the whole thing as you could not get parts. Thank you for the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rosemary from holyoke, MA
- Parts Used:
- WH01X10302
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
the belt is so tight
I heard this is a tool you need to get that belt on with out slipping off. we thought we had the wrong size belt it as impossible at first to get the belt on. what a struggle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James C from HINESVILLE, GA
- Parts Used:
- WH01X10302, WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Socket set
Replaced the rib belt.
I watch a YouTube video. Showing how to put the new belt on with a zip tie. 100 percent. Success. Thank you for the correct part.replacing the drain was very ease. Use a socket set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Branson, MO
- Parts Used:
- WH01X39337, WH02X10383
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Socket set, Wrench (Adjustable)
Washer tub leaking
I watched the YouTube video. Great help. The part was at my house less than 24 hours after I ordered. Great delivery! The repair was a no brainer even for a novice like me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ELMIRA, NY
- Parts Used:
- WH41X365
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Pressure Switch fill hose plugged.
I followed the repair video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pansy from STARKVILLE, MS
- Parts Used:
- WH12X10334
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Washer wouldn't spin out
Someone did it for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Murphy, TX
- Parts Used:
- WH2X1197
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Socket set, Wrench (Adjustable), Wrench set
The machnica had recently developed a rumble during the spin cycle
The first thought regarding the light rumble during the spin cycle is that the bearing was going bad. Many of the other inputs on replacing the bearing included the problem with removal of the Hub Nut. Only one article noted a set of assembly instruction for the washer is clipped onto the upper rear panel behind the control knobs, but I did not see this comment until later. Not being sure where to start with diassembling the washer, I began by taking off the control panel and to my pleasant surprise I found a neatly folded set of detailed instructions. Following the instructions, I proceeded to quickly disassemble the washer until I got to the HUB NUT. The Hub Nut is an aluminum, 1 -11/16 inch, left hand threaded problem. My tool selection is somewhat limited, so after unsuccessfully attaching it with grippers and vice grips, supported with the liberal aid of a rubber mallet and plenty of WD40, I went looking for something with which I could a better grip on the hub nut. The grippers and vice grips would slide a bit when hit with the mallet. Also since the space is very restricted, a large wrench could not be used. I located a 9-inch pipe wrench, and with the rubber mallet the Hub Nut finally loosened after just a few hits. I replaced the old bearing which appeared to be in fair condition. While replacing the bearing has not solved my noise problem, I thought that my experience with the pipe wrench benefit someone else in their efforts to get the hub nut off without using a chisel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Hollywood, FL
- Parts Used:
- WH02X10383
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
replaced leaky tubseal
Repair went great. The large nut had to be soaked to free it but the part was an exact fit.
Was this instruction helpful to you?
Thank you for voting!