GCWN4950D2WS General Electric Washer - Instructions

Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.

Disassembled washer removed shaft and drive tube assembly reinstalled new unit and replaced split nut during assembly.

I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.

Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.

Ordered lid switch from parts select via website. Two days later I received the part in the mail. Instead or re-wiring, I cut wire close to existing bad switch. Splice two wires and cap with wire nuts. Zip tie loose wire to tub housing.

unscrewed back top cover. unscrewed control panel, replace new control panel.

Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!

The washer came apart fairly easy until I tried removing tub nut Huge Problem!! After beating the spanner wrench to death I purchased a $50 43mm impact socket to remove the nut. I cleaned up the tub and shaft and started reassembly by replacing bearing 6006rs that I found locally. When I started installing the tub seal I ran into a major issue. Seal would not fit properly, it was to loose in tub. The seal was not large enough for outside diameter. It was a 1/16 of inch or so off. I tried two seals and neither one would work. After talking with a retired repair tech I found that the tub was bad and that the old seal had corroded so bad that it expanded the tub seal housing. I decided not to spend anymore money for this junk of a washer and I applied rtv sealant & reassembled. I'll use it until it breaks down and trash it, very bad design for tub seal, nothing holds it in place, pushed up out of tub. I don't think the rtv sealant well hold for very long. I do appreciate the instructional video for repairs, they are very helpful for showing procedures as to the repair but it's a new machine that's used and everything comes apart so easy. 5 year old washer doesn't come apart that easy. It took 2 weeks to fix it after waiting on parts and doing a unconventional repair to tub seal. So now my wife has started searching for another washer because this one is running on a prayer!

FIRST, TURNED OFF THE MAIN VALVE INTO THE HOME..AND BLED THE LINES. USED A SMALL BUCKET AND DISCONNECTED THE LINES FROM THE WASHER. TOOK THE PLATE OFF THE WASHER AND DISCONNECTED THE OLD INLET VALVE CONNECTED THE NEW VALVE AND REPLACED THE COVER PLATE. SINCE I HAD THE MACHINE DISCONNECTED, I PUT NEW WATER LINES AND REPLACED THE HAT AND COLD WATER VALVES WITH NEW 1/4 TURN BOILER BALL VALVES. TURNED THE WATER BACK ONTO THE HOUSE AND RAN THE FAUCET SO THERE WOULD BE NO AIR IN THE LINES WHEN I TURNED THE WATER ON TO THE WASHER.

Popped off the front panel and removed two screws that help top down. Then pulled the top of the washer up and leaned back out of way.Then each strap had a screw on each end and a clip that holds straps just remove the old and replace with new and put back together.

First I googled the problem. Then ordered your part, from specs on your website. Went to Lowes and bout butt splicers. Then when I got email that it shipped I watched the video attached. Awesome. Very proud as I am a woman. Video was excellent. Thank you, Maureen

Removed all four knobs, Took back off removed control board replaced with new one

used a socket to unscrew the clip. pulled out the old hose, slid the new hose into the clip and screwed the clip back on. all fixes should be this easy.

Removed center fabric softener cup. removed agitator holding NUT & washer. Lifted off agitator. Pried off Coupling Pulsator.
Cleaned off all parts (soap Scum )
Installed new Coupling Pulsator (tapped gently down with wood hammer handle) Installed agitator& hold down nut&washer. Installed softener cup.
Job done & noise gone .
Thanks Part Select

You tube is the only way to go!

Followed video to take washer apart. I used the Shaft & Drive Assembly to tap out bearing as it was stuck. BTW the screeching was because the Shaft & Drive Assembly ball bearing retainer cage was in pieces. Replaced tub bearing and installed new Shaft & Drive Assembly. Washer now runs like new. Get the spanner wrench to remove existing nut and purchase a new nut.