GFWH1200H1WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Miguel from Jacksonville, FL
- Parts Used:
- WH13X10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
The washer stop and blinks in the RINSE MODE
I called a repair person to check my 15 months old GE front loader washer that stopped in rinse mode. After his inspection he said it was a deffected computer board and it would be very expensive to replace the 3 computers boards inside and it would be cheaper to buy a new top loader washer. The next day I lifted the top cover and found a taped plastic envelope with instructions titled “For service Technicians Only." On page 2, instruction on to how to enter the washer in to service mode and to test the washer:
Press : Signal, Delay, Signal, Delay (within 30 seconds of plug in washer)
Then rotate main knob to #102 and press Start:(the washer did a test for finding the problem) , and for me was : E22 , it means : replace solenoid valve assembly.
So I order the part from Partselect.com for $58.00 and my Washer runs beautiful, thanks to the instructions inside.
Press : Signal, Delay, Signal, Delay (within 30 seconds of plug in washer)
Then rotate main knob to #102 and press Start:(the washer did a test for finding the problem) , and for me was : E22 , it means : replace solenoid valve assembly.
So I order the part from Partselect.com for $58.00 and my Washer runs beautiful, thanks to the instructions inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felipe from Houston, TX
- Parts Used:
- WH13X10029
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
stops at rise
removed 5 screws, unscrew two more screws, remove the houses and disconnect the wires remove the watter valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denise from BRANCHBURG, NJ
- Parts Used:
- WH01X20826
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Shock absorber sheared off from drum out of balance
2 things to note if you’re going to replace this part. First, you definitely need the 6” crescent wrench as noted in the instructions. Second, tape up the flanges of the machine so you don’t cut your arms to pieces on sharp metal edges.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from GRAND JCT, CO
- Parts Used:
- WH10X20821
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
You shut the door washer would beep twice, and start button would flash.
First I locked out the power cord. I pulled the back screws to the top panel off, slid the top panel to the back of the washer, and pulled the top off. opened the washer door, and ran my down where the door switch was. with one hand on the switch, I use the other hand with a philips screw driver to remove the screws on the door switch. Pulled the switch up just enough to remove the electrical plug. Now installation will be the same but start backwards. Plug in the switch, run the switch into the housing. While holding the switch in place with one hand use the other hand to install the two screws. Replace the top panel, remove any lockouts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from MINNEAPOLIS, MN
- Parts Used:
- WH13X10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
washer would stop at certain points in cycle
Replace the water valve according to the youtube video from this site. It was really easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herman from SAN DIEGO, CA
- Parts Used:
- WH11X34741
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water leaking
Did not have to use the new pump filter. The old one finally worked. I probably didn’t screw it in tight enough.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Los Angeles, CA
- Parts Used:
- WH13X10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Washer keeps Pausing.
After getting error message from washer, Looked it up and found if the water lines are find, then replace the water valve. After replacing the valve, everything works fine.
Was this instruction helpful to you?
Thank you for voting!