GTAN4250D2WW General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Arlis from Moore, SC
- Parts Used:
- WH01X39337
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Tube Shaking Like Out Of Balance. Water Not Draining Completely And Created An Unpleasant Odor
Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joel from mt vernon, IL
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
two tub dampening straps snapped
I just watchied the clip on the website during the day about how to fix it, went home that night and fixed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cynthia from winter park, FL
- Parts Used:
- WH41X10096, WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
washer leaked water
after reading repair stories, decided I should take front panel off and see where leak was coming from. taking the panel off was real pain but well worth as inside was dry! so I looked again and discovered a pin hole in drain hose that only leaked when tub was full. while I had panel off I noticed tub dampening straps were broken so went ahead and ordered those parts too.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timmy from Fairport, NY
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Banging noise when it was agitating
removed front washer cover (2) clips at top released with straight screwdriver . removed washer top cover (2) 1/4" head screws that are behind front washer cover. Then removed screws holding tub dampening straps (4)5/16" head from agitation drum housing from top, removed other end of strap from under side (4) 1/4" head screws. then assembled with new straps in reverse order. easy repair nice and quiet again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gustavo from Harlingen, TX
- Parts Used:
- WH01X39337
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Shaking and making loud noise
removed three screws from back panel used putty knife to remove front panel and dampening strap were there to remove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from Bynum, TX
- Parts Used:
- WH41X22935
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
had a pin hole in the drain pipe
order the part and replaced it and it works just great! May I add never before have I had such an amazing experience in dealing with your company, your company shows pictures and I ordered the part in the late afternoon and I had it the next day, the diagram you show on your site was so helpful, you told us that the part now is replaced with a different #. Once again KUDOS!! to your co.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Priscilla from Beverly, MA
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
broken dampening strap
Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.
Replaced four broken dampening straps, washer is quiet and all is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- larry from Steamboat Springs, CO
- Parts Used:
- WH01X39337
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broken tub strap
follow youtube vid. simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Port Hueneme, CA
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Leaking
Remove front panel by pulling on both sides of it at top.
Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.
Replace hose and re install clamps.
Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.
Replace hose and re install clamps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from ROCHESTER, NY
- Parts Used:
- WH01X10302
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had to replace drive belt on washer
I removed the front cover on washer I tied wrapped one side of the belt to to the back pulley and placed the belt on the the motor pulley then placed the belt installer on pulley below belt with gloves on I started rotating the pulley in the back and when it started getting s little tight I moved pulley back and forth then started turning in clockwise direction again and belt went right on.i cut the tie wrap after making sure belt was secured and evenly on then turned pulley to make sure belt was secured removed belt installer and replaced front cover.i am a 57 yr old woman and did this job by myself.so easy when you have the belt installer also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from Spring city, PA
- Parts Used:
- WH12X10334
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bad lid switch
Watched the how to video, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from BERKLEY, MA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Plastic pipe developed a tear and leaked drain water.
Shut off power, removed both water hoses, detached drain hose, noticed the plastic drain hose was splitting, entered the model number in a web search, ordered part from PartSelect. received part next day and reversed previous process. Tested repair and no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dirk from State College, PA
- Parts Used:
- WH41X10096
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old drain hose was cracked
old one out, new one in. new one is seated, but not a perfect match bracket to hold hose in washer does not fit on this replacement hose properly. But I feel comfortable with the result & use
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stanley from Pownal, VT
- Parts Used:
- WH43X10034
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Replaceed agitator
Old agitator was stuck on and i could not pull it of.I used two claw hammers and put the claw under the agitator and broke it free.Worked perfect" Took five minutes "
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Tallahassee, FL
- Parts Used:
- WH41X22935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Small leak from a tiny hole in the drain hose
Simply unclamped the lower end of the hose, then used the nut driver to release the upper clamp of the hose. Took it off, replaced it with the new hose and re-clamped both ends. It took me about 12 minutes to do this. Very easy repair!!
Was this instruction helpful to you?
Thank you for voting!