Models > GTAN5250D2WW > Instructions

GTAN5250D2WW General Electric Washer - Instructions

Jump to:

All Instructions for the GTAN5250D2WW
121 - 135 of 226
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
larry from Steamboat Springs, CO
Parts Used:
WH01X39337
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
broken tub strap
follow youtube vid. simple
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Oraila from RINCON, GA
Parts Used:
WH43X10034
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
broken part
We pulled out the old parts and then we got the new parts and we put them in,
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rachel from Spring city, PA
Parts Used:
WH12X10334
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Bad lid switch
Watched the how to video, very simple.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Shirley from Kiln, MS
Parts Used:
WH41X10096
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
the hose that came on the machine was too short for a mobile home hookup
Pullout the old hose and put in the. New hose. Did it myself, and I'm a 58 yr old female. Easy,easy.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Amy from ROCHESTER, NY
Parts Used:
WH01X10302
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Had to replace drive belt on washer
I removed the front cover on washer I tied wrapped one side of the belt to to the back pulley and placed the belt on the the motor pulley then placed the belt installer on pulley below belt with gloves on I started rotating the pulley in the back and when it started getting s little tight I moved pulley back and forth then started turning in clockwise direction again and belt went right on.i cut the tie wrap after making sure belt was secured and evenly on then turned pulley to make sure belt was secured removed belt installer and replaced front cover.i am a 57 yr old woman and did this job by myself.so easy when you have the belt installer also.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sallie from WEAVERVILLE, NC
Parts Used:
WH43X10034
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
All of the fins on the bottom had broken due to clothes getting caught in them.
Removed the softener despenser by pulling it straight up, then did the same with the agitator, except I had to turn it a little then pull straight up.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Annamarie from FORT LORAMIE, OH
Parts Used:
WH43X10032
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Agitator did not agitate
Removed agitator with rope idea. One quick jerk and it came off. Removed coupling. Replaced with new coupling. Reinstalled agitator. Works fine. Note: I could not see anything wrong with the old coupling. It looked brand new with no noticeable wear!! Thanks for your help in recommending the part that most likely would fix the problem.Tom
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Belinda from FLORENCE, KY
Parts Used:
WH41X10096
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
cracked drain pipe
Remove two bracket screws. Removed hose. Put new hose in place using same bracket and screws. inserted end of hose into washer drain. Secured hose to cold water hose with two zip ties.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Douglas from OVERLAND PARK, KS
Parts Used:
WH12X10334
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Water temp will fill hot only with lid open. Close the lid and it is cold water only.
The video I watched said to remove front panel, control panel, and top panel. After I removed the front panel, I was able to remove the lid switch and splice the wires together and reinsert in the mounting without removing the other panels. Secured with wire tie and put front panel back in place. This did not, however fix the problem.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
tiberiu from CLEVELAND, OH
Parts Used:
WH43X10034
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
AGITATOR BROKE
pulled up on agitator and it came off and replaced it with the new one
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
stanley from Pownal, VT
Parts Used:
WH43X10034
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Replaceed agitator
Old agitator was stuck on and i could not pull it of.I used two claw hammers and put the claw under the agitator and broke it free.Worked perfect" Took five minutes "
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kathy from Tallahassee, FL
Parts Used:
WH41X22935
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
Small leak from a tiny hole in the drain hose
Simply unclamped the lower end of the hose, then used the nut driver to release the upper clamp of the hose. Took it off, replaced it with the new hose and re-clamped both ends. It took me about 12 minutes to do this. Very easy repair!!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOHN from BERKLEY, MA
Parts Used:
WH41X10096
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Wrench (Adjustable)
Plastic pipe developed a tear and leaked drain water.
Shut off power, removed both water hoses, detached drain hose, noticed the plastic drain hose was splitting, entered the model number in a web search, ordered part from PartSelect. received part next day and reversed previous process. Tested repair and no leaks.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dirk from State College, PA
Parts Used:
WH41X10096
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
old drain hose was cracked
old one out, new one in. new one is seated, but not a perfect match bracket to hold hose in washer does not fit on this replacement hose properly. But I feel comfortable with the result & use
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roger from Port Hueneme, CA
Parts Used:
WH41X22935
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Socket set
Leaking
Remove front panel by pulling on both sides of it at top.

Loosen clamps on both ends. Tub end uses 5/16 socket on extension. Pump end uses plyers.

Replace hose and re install clamps.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GTAN5250D2WW
121 - 135 of 226